Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
w - Value 1 All notes off Third wH : OH - FH (0 - 15) : ООН. 7FH (0.127) 0 = ch.l - 15-ch.16 0 * OFF. 127 = ON When All notes off is recognized, all the notes which have been turned on by MIDI Note on message are turned off. Status BnH Second 7BH n = MIDI channel No, Third ООН :0H - FH (0 - 15) 0 = ch.l - 15-ch.16 81 ■ System real time messages • Active sensing Once recieving this message, the Mode! 760 expects to accept status or data in sequence, at last within about 400 msec intervals. If the unit fails to recieve a message 400 msec after previous one, it judges there is a problem somewhere in MIDI path, muting the current sound, set as reset ail controllers is recognized. After "MIDI Comunication Emir" is displayed, it will be back into normal condition but monitoring 400 msec - interval of incoming signal. Status FEH ■ System exclusive messages A set of various parameter is received using MIDI Exclusive messages on Model 760. Refer to section 3 (p.47) and ’Roland Exclusive Messages’ (p.76) for details. Status F0H data (EOX) ddH ..............F7H F0K = System exclusive ddH - data : 00H - 7FH F7H - EOX (End of Exclusive) 2 TRANSMITTED DATA ■ Channel voice messages The message is transmitted through the MIDI Channel for Upper/Lower.(p.55) • Note event If Chase/"Arpeggio (Key Effect) is set at “On," note events for chase/arpeggio effect is transmitted through the Part’s MIDI channel coresponded to “Chase Part" / “Arpeggio Part” O Note off Status 8nH Second kkll n = MIDI channel No. kk = Note number vv = Velocity О Note on Status 9nH Second kkH n - MIDI channel No. kk » Note number vv - Velocity Third wll : OH - FH (0 - 15) : 00H - 7FH (0 - 127) : 01H - 7FH (1 - 127) Third wll : OH - FH (0 15) : 00H - 7FH (0 - 127) : 01H - 7FH (I - 127) 0 = chJ - 15 = ch.16 0 = C - 1 - 127 = G9 0-ch.l - 0 = C- 1 I5 = ch.l6 127 = G9 • Control change O Modulation depth This message is transmitted when the Modulation Lever is used. Status Second BnH 0IH n = MIDI channel No. w = Modulation depth Third wll : OH - FH (0 - 15) : ООН - 7FH (0 - 127) 0 = ch.I - 15 = ch.I6 O Hold 1 This message is transmitted when the Hold Pedal is depressed. * * * Transmission of RPN *** While selling Tuning (p.22), press the [WRITE] button then the Fine tune (RPN £ 1) is transmitted through the Control Channel. RPN # I : Fine tune BnH 64H 01H BnH 65H OOH BnH 26H HH BnH 06H mmH (RPN LSB) (RPN MSB) (Data LSB) (Data MSB) n ■= Control channel No. : OH - FH (0 - 15) II - LSB data of the Fine tune : 00H - 7FH mm = MSB data of the Fine tune: 1FH - 60H mmH.HH = 1FH.00H - 40H.D0H - 60H.1BH (-50.5cent - Ocent t A = 440.0Hz 0 - ch.î - 15 = ch. 16 - 50.3cen0 О RPN LSB Status BnH Second 64H n - Control channel No. 01 = LSB of the Fine tune О RPN MSB Status BnH Second 65 H n = Control channel No. 00 = MSB of the Fine tune O Data entry LSB Status BnH Second 26H Third 01H : OH - FH (0 15) Third OOH : OH - FH (0 - 15) Third Ш1 0=ch.l - !5 = ch.l6 0 = ch.l - 15 = ch-16 n - Control channel No. :0H - FH (0 - 15) II = LSB data of the Fine tune :OOH - 7FH (0 - 127) O Data entry MSB O-ch.l - I5 = ch.l6 Status BnH Second Third 06H mmH n = Control channel No. :01I - FH (0 - 15) mm = MSB data of the Fine tune: IFH - 60H (31 96) 0 - ch.l - 15--ch.16 • Program change This message is transmitted when MIDI Program Change function is on.(p.55) Status CnH Second PPH 0 = ch.l - 15--ch.16 n = MIDI channel No. : OH - FH (0 - 15) pp = Program change number : OOH 7FH (0 - 127) O Tone change number When the TONE SELECT or VARIATION button are pressed, the Tone change number corresponds to that tone is transmitted through the MIDI Channel for current part. Refer to TONE LIST (p.70) for program number. Tone* : Tone Name CnH ppH 1 : A.PIANO 1 00H 128 : DRUMS 7FH n = MIDI channcl No. for current part : OH - FH (0 - 15) 0= ch.l - 15 = ch.16 Status BnH Second 401! Third wll MIDI channel No. = Hold : OH - FH (0 - 15) : ООН. 7FH (0.127) 0 = ch.l 15 -^ ch.16 OFF » 0, ON - 127 82 O Patch change number When the USER PATCH button is pressed, the patch change number corresponds to that patch is transmitted through the Control Channel. Patch 3_CnH noH_ USER PATCH A - î OOH USER PATCH C-8 I7H n = Control channel No. : OH - FH (0 - 15) 0-ch.l - 15-ch.l6 • Channel Aftertouch This message is transmitted when holding down the key by the MIDI After function is on. Status Second DnH vvH n = MIDI channel No. : OH - FH (0 - 15) 0 = ch.1 I5=ch.l6 vv - Value : 00H - 7FH (0 - 127) • Pitch bend Change This message is transmitted when the Bender Lever is used. Status Second Third EnH IIH mmH n = MIDI channel No. : OH - FH (0 - 15) 0 - ch.I - I5^ch.l6 II = LSB of Pilch bend change : OOH - 7FH (0 - 127) mm = MSB of Pitch bend change: 00H - 7FH (0 - 127) mmH,IIH = 00H,00H - 40H.00H - 7FH.7FH (-8192 - 0 - -8191) mmH IIH_Relative value of Pitch OOH OOH -8...