Оценок - 2, средний балл: 4 ( )

Производитель: Roland Размер: 937.62 kb Название файла: Язык инструкции:

SUB OUT, Effect Send and AUX Send circuits, then sent to the MASTER OUT, SUB OUT, Effect Send and AUX Send.

d, MASTER OUT Left and Right signals input to a channel {where the Output Select Switch MASTER is set to “on"), and signals input via the RETURN, EXT IN or BUS IN (MASTER) jacks will be mixed. The mixed signal's level is adjusted by the Master Balance control (L and R volume balance), then adjusted again at the Master Volume control before being output from the MASTER OUT jacks. e. SUB OUT Left and Right signals input to a channel {where the Output Select Switch SUB is set to ’on"), and signals input to the BUS IN ( SUB ) jacks will be mixed. The mixed signal's level is adjusted by the Sub Balance control (L and R volume balance), then adjusted again at the Sub Volume control before being output from the SUB OUT jacks. f. MONITOR OUT Signals {pre-fader : before the MASTER Volume control or SUB Volume control) selected at the Monitor Select Switches (MASTER/SUB) and signals from the BUS IN (MONITOR) will be mixed and level-adjusted at the Monitor Out Volume control. The resulting signals are then sent to the MONITOR OUT jacks {the same signal will also be sent to the Headphone jack). g. Effect Send (EFFECT 1-3 SEND) Signals from the Effect Volume control of each channel and from the BUS IN jacks {EFF 1-31 are mixed and level-adjusted at the Effect Send Volume control, then sent to the Eff (Effect) Send jacks. h. AUX Send (AUX SEND) Signals from the AUX Volume control of each channel and from the BUS IN jacks (AUX) are mixed and level-adjusted at the AUX Send Volume control, then sent to the AUX Send jack. 7 8 2 PANEL DESCRIPTIONS 1. Channel Section m~ i roiK/g»0 PBW/SISO PEAK/316 O -10 , , -10 . . -10 (2) SENS Knob Use this knob to adjust the input sensitivity according to the level of the incoming signal. The appropriate position of this knob is the point at which the PEAK/SIG Indicator is green, and red only on the highest input peaks. If the PEAK/ SIG Indicator does not light at all with a signal present, set the SENS Knob higher or increase the input level. * The input range is -30 dBm to +4 dBm. (3) Panpot Knob This knob positions the sound within the stereo sound field. At the center position, the sound will be heard from the center of the sound field. (4) Effect Volume Knobs (1-3) These knobs control the level of the signals being sent to the Effect Send jacks. * The signal to be sent to the Effect Send jacks is extracted after the Channel Volume Knob (Post-fader). * The Effect Volume Knob will not function unless the Output Select Switch MASTER is turned on in the channel where the effect is to be used. (5) AUX Volume Knobs These knobs adjusts the level of the signals to be sent to the AUX Send. * You can select the point at which the signals sent to AUX Send are extracted using the AUX Select Switch. * When "POST" is selected with the AUX Select Switch, the AUX Volume Knob does not function unless the Output Select Switch "MASTER" is turned on in the channel where the effect is to be used. © Peak Signal Indicator These indicators will be green when signals are fed into the CHANNEL INPUT jacks. The indicators become red if the signal level is excessive. In other words, indicators are green when the signal level is -20dB of nominal level after passing the input sensitivity circuits, and red at -6dB of the clipping level. (6) Output Select Switch (MASTER/SUB) These switches select the output jacks (MASTER OUT or SUB OUT) for the signal from each channel. (7) Channel Volume Knob These knobs control the overall level of each channel's signal before being sent to the Master section. * The nominal output of the Channel Volume Knob is obtained when it is set to "10". 9 2. Master Section CD Return Volume These knobs adjusts the level of the signal fed into the RETURN jacks. * The nominal output of Return Volume is obtained when it is set to "10". (2) EXT IN (External In) Volume This knob adjusts the level of the signal fed into the EXT IN jacks. * The nominal output of the External Volume is obtained when it is set to "10". (3) EXT IN (External in) Jacks This is where external devices (eg. another mixer) are connected to the M-240R. It consists of a stereo pair, but can be used in mono by using the Left [ L(Mono) ] side only. (?) Effect Send Volume These knobs control the final output level of the effect signal of each channel. The signal is extracted after the Channel Volume Knob (Postfader). * The nominal output of the Effect Send Volume is obtained when it is set to "8". (D AUX Send Volume This knob controls the final output level of the AUX signal of each channel. * The nominal output level is obtained when the AUX Send Volume is set to “8". (6) AUX Select Switch This switch selects the point at which the signal to be sent to the AUX Send is extracted from the signal path. In the PRE (pre-fader) position, the signal is extracted befor...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: