Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
When necessary, adjust the overall volume with the Master Volume again. 11 2. Setup example with effects device. Speaker System r DA-1500 ] LSRS-120 etc. J Power Amplifier r SRA-2400 I [SRA-1200 etc. J Equalizer, Limiter etc. [E-660 etc.] i i i ®| 1® fT Lt 1 1 { i oooool^lisD Effector [SDE-3000A, DEP-5 etc.] Effector [DEP-3, DEP-5 etc.] tJ lie: id § § (p <$ CD G O ô 0' Q & IQQ Q Q & Q ■ Effect Processing with delay, reverb, etc. 0 Raise the Effect Volume of the desired channel to an appropriate level. Set the overall output level using the Effect Send Volume in the Master Section and the input level meter on the effect device. (2) Adjust the level from the effect device with the Return Volume. * The direct sound is processed within the mixer, so return only the effect sound to the mixer. * The signal from the Effect Send will be taken after passing the Channel Volume. * By connecting an effect device to the Channel Insert Jack, an effect signal can be directly mixed at the channel. * When a separate unit (e.g. equalizeretc.) isconnected between the mixer and power amplifier, you can control overall sound or tone quality. 12 3. Monitoring (Fold back) / Monitoring with Monitor Out. W ° M*»., o 6 o G> Ö O 6 Q 6 Q Q © Graphic Equalizer etc. |o_______ [GE-131 (BOSS) etc.] ¿ml! (Metronome Out) Power Amplifier r SRA-2400 1 LSRA-1200 etc.J Speaker System [DA-1500 ] LSRS-120 etc.J ^]BOS^ ooo D ooo «=> Monitor Amp [MA-12 (BOSS) etc.] Sequencer etc. rMC-BOOMkQl LMC-300 etc.J ■ Monitoring (Fold back) © Rotate the AUX Volume of each channel to "PRE”. Adjust the output level of the sound you wish to monitor. (2) Adjust the overall volume with the AUX Send Volume in the Master Section. * No matter where the Channel Volume or Master Volume is set, you can adjust the mixing balance of the monitor or volume. * By connecting an equalizer or limiter between the mixer and power amplifier, you can control overall sound or tone quality. ■ Monitoring with Monitor Out: 1. After adjusting the volume of each channel, adjust the monitor volume with the Monitor Out Volume control. 2. Raise the Monitor In Volume to balance with the channel volume. * The signal fed into the Monitor In will not be sent from the Master Out. * The Peak Meter does not indicate the signal sent from the Monitor In. * You can adjust the monitor volume regardless of the position of the Master Volume. * By connecting an equalizer or limiter between the mixer and power amplifier, you can control the overall sound or tone quality. 13 4. Stacking example (Master) * Connecting two or more mixers to increase the number of channels is called "stacking". The above diagram shows an example of stacking using two M-12Es. By stacking, effects processing for two (or more) mixers can be accomplished by one effects device. 14 IT! Level Diagram 15 Input Jack Input Sensitivity Rated Input Level Input Impedance Recommended Source Impedance Type of Connector CHANNEL INPUT (SENS=MAX) CH1-12 -66 dBm (0.39 mV) -60 dBm (0.78 mV) 5.5 ka Less than 1 ka PHONE INSERT (RETURN) CH1 -4 -6 dBm (388 mV) 0 dBm (775 mV) 20 kO Less than 2 kQ STEREO PHONE RETURN RTN 1 (LEVEL: -20 dBm) -26 dBm (38.8 mV) -20 dBm (77.5 mV) 20 ka (STEREO) 10 ka (MONO) Less than 2 ka (STEREO) Less than 1 ka (MONO) PHONE RTN 2 -2 dBm (615 mV) +4 dBm (1.23 V) 20 ka (STEREO) 10 kO (MONO) Less than 2 ka (STEREO) Less than 1 ka (MONO) PHONE MONITOR IN MON IN -26 dBm (38.8 mV) -20 dBm (77.5 mV) 10 ka (STEREO) 5 ka (MONO) Less than 1 ka PHONE BUS IN EFFECT, AUX -2 dBm (615 mV) +4 dBm (1.23 V) 10 ka Less than 1 ka PHONE [5l Input/Output Standard % : 0 dBm=0.775 Vrms 1:600 Q. Loaded 2: Both Channels 100Q Loaded Output Jack Rated Output Level Non-Clip Max. Output Output Impedance Recommended Load Impedance Type of Connector MASTER OUT (BALANCED) +4 dBm*1 (1.23 V) +20 dBm*1 (7.75 V) 600 q More than 600 Q XLR Connector (XLR-3-32) MASTER OUT (UNBALANCED) +4 dBm* (1.23 V) +20 dBm (7.75 V) 300 Q More than 3 kQ PHONE MONITOR OUT +4 dBm (1.23V) +20 dBm (7.75 V) 1 kQ (STEREO) 500 Q (MONO) More than 10 kQ More than 5 kQ. PHONE INSERT (SEND) (CH1 ~4) 0 dBm (775 mV) +20 dBm (7.75 V) 200 a More than 2 kQ. PHONE SEND (EFFECT.AUX) +4 dBm (1.23 V) +20 dBm (7.75 V) 3oo a More than 3 kQ PHONE PHONES — 100 mW+100 mW*2 ioo a More than 8 kQ STEREO PHONE ■ Output Standard [61 Specifications Frequency Response Total Harmonic Distortion: Noise Level: Input Equivalent Noise: Residual Noise Cross Talk Equalizer HiGH EQ LOW EQ Power Consumption Dimensions Weight 10 Hz - 60 kHz+_2 dB (SENS=MIN) Less than 0.03% (SENS=MIN, 20 Hz - 20 kHz at rated output) (Input short, IHF-A, Typ.) -124 dBm -101 dBm [All Faders :min] -79 dBm (Master Fader :max] [All Channel Faders :min) -78 dBm (Master Fader :maxi [All Channel Faders :maxj [AH SENS. :minl -41 dBm (Master Fader :max] [All Channel Faders :maxj [All SENS. :max] Less than -70 dB (1 kHz betwe...