Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Each time you press[_+ ], the key is raised by a half note. Each time you pressjj- j, the key is lowered by a half note. j * The maximum range of transposition is within one octave 39 4. For Better Performances b. Master Tune This function allows you to change the master tune of the instrument that you are using. Use this function to match the tuning of instruments when you are playing in an ensemble with other instruments. The master tune setting range is from 415.3 Hz to 466.2 Hz, and you can make changes in units of 0.1 Hz. The master tune setting is retained even after the power is turned off. Operation From the "Master Screen" 0 Press ( TRANSPOSE /TUNE/ BEND J until the Master Tune "Control Screen" is displayed. * If another "Control Screen" is displayed, pres? C TRANSPOSE / TUNE / BEND) again to obtain the Master Tune "Control Screen". The pitch that is displayed is the value that was previously set. (2) Next adjust the pitch. The pitch is raised by pressing f -f j and lowered by pressing - * The pitch that you set will be retained in memory even if the power is turned off, until you change it again. * When shipped from the factory, the master tune is set at 440.0 Hz. 40 c. Pitch Bender Range The range over which the pitch bend effect is obtained (pitch bender range) can be set to suit the contents of the music that you are playing. (For details on the pitch bend effect, see page 12.) Operation From the "Master Screen" 0 Press the [ TRANSPOSE / TUNE / BEND J button until the Pitch Bender Range '"Control Screen" is displayed. The pitch bender range that is displayed is the value that was set previously. * li another "Control Screen" is displayed, pres^ „ ( TRANSPOSE / TUNE / BEND') again to obtain the Pitch Bender Range "Control Screen" ’ ; , A point of advice Although it is possible to set the pitch bender range as wide as possible to obtain a dynamic effect, a setting of [1—3] for ordinary playing will make it easier to control. © Next adjust the pitch bender range. The pitch bender range is raised a half note each time you press: + and lowered one degree each time you press T— The range of change, up or down corresponds to that shown below: 00 = No change 01 = Semitone 02 = Major 2nd 03 = Minor 3rd 04 = Major 3rd 05 = Perfect 4th 06 = Augment 4th 07 = Perfect 5th i * The default setting is "02 (two intervals}." 08 - Augment 5th 09 = Major 6th 10 = Minor 7th 11 = Major 7th 12 = Octave * The range setting is retained in memory until the next time that you change it, even if power is turned off. 41 4. For Better Performances d. Octave Shift Using this function, it is possible to shift either the Upper or Lower parts by units of an octave. What is octave shift? For example, shifting up by one octave is shown in the diagram below: IIIII III II When you play the "GO" key, a tone with the pitch "G1" is produced. Shifting down by one octave is shown in the diagram below: When you play the "EG", a note with the pitch of "E-1" is produced. Shifting the notes that you play in octave units in this way is called octave shift, and this function can be used to match the tone range of either the Upper or Lower Tone to a pitch that is appropriate for that part. Operation From the "Master Screen" © Press OCT.SHIFT . OCTHUE SH I FT [... ü W E R 0 U F' P E R 0 © Next press the Upper or Lower balance button Q/[v]. Each time that you press [a] , the tones are shifted up one octave, and each time you pressQ , the tones are shifted down by one octave. The available range is -2~+2 octaves. (For details on balance of partrs, see page 45). 0 Ü T H U E S H I F T !.... 0 W IE R -i- 1 !.J F’ F;: E R ^ 2 | * The octave shift funrtion cannot be used with drums, bass, or accompaniment * This junction is active while the Octave Shift LED is lit. To turn off the LED, change the settings back to "LOWER 0, UPPER 0" in the "Control Screen". 42 e. Pedal Switch Function The right and left pedals are used not only as Damper/Soft pedals, but also can be assigned one function from among 9 available panel functions, thus allowing foot control over the function. A point of advice Upon power up, the Damper pedal works only with respect to the Upper Tone. A point of advice Sustain effect can be obtained in the Lower tone by using the Damper of . Lower function. ; Right pedal • Damper of Upper # Rhythm Start/Stop 'START /STOPl) TQ~VARÎÂTION ) # Fill-in to Variation (I TO ORIGINAL # Fill-in to Original (j INTRO/ENDING j) • Intro/Ending (f SPLIT j) • Split on/off (( ARRANGER i) • Switch between BASIC and ADVANCED Arranger (j MELODY INTEUJGENCTj) • Melody Intelligence On/Off > • Damper of Lower Left pedal • Soft • The same functions can be performed with the right pedal except sostenuto, eight functions in all. > The seven functions that can be used by pressing down these two pedals (except for soft and sostenuto) operate in the same way j as the buttons enclosed in parent...