Оценок - 6, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
43) or "Chorus Type" (p. 45) is not set to OFF? -* Select a type other than OFF. Is the Reverb Level suitable? (p. 42) -* Set the Reverb Level to an appropriate value. Be aware lhal the internal effects of the GR-09 are designed to work only on the synth sounds. They cannot be applied to the guitar sound itself. -* You can apply effects to only the guitar sound using an external effects unit, by utilizing the GUITAR OUT jack. (If using a single amplifier for both the synth and guitar sounds, the GUITAR RETURN jack is used as well.) 69 TROUBLESHOOTING Pitch of Synth Sound Does Not Change With That of the Guitar It is normal for certain Tones (such as special effect sounds) to exhibit a different kind of pitch change compared with the guitar. Cyclic Noise Heard in the Very High Pitch Range This is caused by a phenomenon common to digital synthesizers known as "aliasing." When you play using a sliding technique, or make use of the Pitch Shift function, you may hear this type of noise. This is normal. The GR-09 was designed to minimize aliasing as much as possible, making it suitable for use with a guitar. Pitch Doesn’t Change Smoothly Could you have the Patch set to “Chromatic"f -+ If the "CHROM" indicator is lit after you press the [EDIT/PLAY] button (and enter the Edit mode), turn it off by depressing the pedal at the far right. (You may want to then write this status into the Patch, p. 40.) Are you making use of the Bend Data Thin (p. 64) feature? When playing normally, some of the natural pitch fluctuations will not be fully expressed when this function is being used. -* Don't use the Bend Data Thin feature unless it is really necessary. Patch Won’t Change When (+)/(-) Buttons are Pressed in the Pedal Function Mode Did you make any kind of editing changes in the Patch before you entered the Pedal Function mode? In order to prevent the loss of data which has not yet been saved (written) as part of a Patch, the unit does not allow you to move away from the Patch currently being edited while in the Pedal Function mode. -* You can switch to whatever Patch you wish if you return to the Play mode. “bAt” is Displayed While Power Is On This is a warning message which tells you that the unit's internal battery (needed for preserving the Patch and System data) is nearly depleted. Once you notice this message, you should have the battery replaced promptly, if you don't want to risk losing your data. -* Please contact your Roland retailer or the nearest Roland Service Station. < While Editing Patches > Display/Indicator Suddenly Started Flashing When the (EDIT/PATCH] indicator begins flashing, it warns you that changes have been made in the currently selected Patch, but they have not been saved. (The same occurs when in the Play mode.) If the displayed number begins flashing when making settings for the Edit Target or Note Shift, and the STRING SELECT knob is set to ALL, it means that the settings for these parameters are not the same for all of the strings. 70 TROUBLESHOOTING Sound Doesn’t Change After Being Edited Changes made for the attack, release, and brightness will sometimes affect only the Main Tone, depending on the setting for the Edit Target. Similarly, settings for Note Shift can sometimes be made to affect only the Sub Tone. -+ Check your setting for the Edit Target and make sure it matches your intentions, (p. 48) If necessary, you could switch the Tone numbers that are assigned to the Main and Sub Tones, (p. 33) On the GR-09, changes made in the attack, release, and brightness involve making adjustments in the original data that is used by the Tone. For this reason, the range in which change is possible will vary depending on the Tone. Some Tones will not seem to change as much as others. Reverb Not Obtained Even With Reverb Level Set High Have you checked to make sure you don't have the Reverb Type set to "OFF"? -» Select a type other than "OFF." (p. 42) < When Using a MIDI Keyboard (or other unit) to Play the GR-09’s Sound Generator > Sound Not Produced Do the MIDI channels on the receiver and transmitter match? -* Set the MIDI channel appropriately, (p. 58) Chords Don’t Sound/Keyboard Damper Doesn’t Produce Effect Are you using "Poly Mode Reception"? (p. 62) Ordinarily, MIDI reception on the GR-09 is set to use the Mono mode. ¡Even when you select "Poly Mode Transmission" when making the MIDI CHANNEL settings, reception will still remain in the Mono mode.) Also, the unit will respond to MIDI Control Change #64 (Damper Pedal) only when it is operating in the Poly mode, (p. 62) -* Set the unit to use this feature by holding down the [-] button while you turn power on. Pedal Functions on the GR-09 Don’t Work When using MIDI messages from an external device (keyboard or other unit) to sound the GR-09, its pedals will not provide their normal functions. Only control over modulation is available. -* Use the external device's controllers if you want to apply be...