Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. C€ For EU Countries This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC. Supplied parts contents • Divided Pickup..........................1 Wirings • Amp Board.................................1 • For GK Connector-A 7-pin ...1 • GK Connector Board.................1 • For GK Connector-B 8-pin ...1 • Plate.............................................1 • For GK Volume 3-pin ...1 • Screw...........................................2 • For Bass Signal 2-pin ...1 • Screw (for installing the Divided Pickup) ...2 • For Switch, LED 6-pin ...1 • Spring (for installing the Divided Pickup) ...2 Parts should be arranged separately • Screw ...4 • Ground Wire ...3 (*1) DO N225 • GK Volume (50 kQ ± 20 % B curve)...........1 • LED ................................................................. 1 • DOWN/S1, UP/S2 Switch (momentary type switch, push: ON) ......... 2 • GK/MIX/BASS Select Switch (1 pole ON-OFF-ON toggle switch) ............ 1 • Nut (for GK Volume) .................................... 2 • Washer (for GK Volume) .............................. 2 Wiring Diagram Divided Pickup C°[ ~ ll BASS/MIX/GK Select Switch When connect the wiring, check the number of pin Output jack of Bass GK Volume 50 kfí ±20 % B curve Dimensional Drawing of the Hole (If necessary, a hole for a rotation-stopper can be drilled.) • GK Volume 7.6 mm >o for a rotation-stopper 0 3.2 mm 0 9.0 mm • GK/MIX/BASS Select Switch j4 mm о__ • DOWN/S1 Switch UP/S2 Switch 0 16.0 mm for a rotation-stopper 0 2.4 mm & Installation Notes GK Connector Board 1. Attach the connector to the plate with the supplied screws. 2. Attach the plate to the bass with the screws. * Mount GK Connector board so that small connection port should be placed top toward bass surface. small connection port For GK Volume Wiring 1. Solder each signal wire of GK volume wiring with volume 50 kQ ±20 % B curve. For Switch, LED Wiring (Select Switch, DOWN/S1 Switch, UP/S2 Switch, LED) 1. Ground wire for each wiring is common. Do wiring as “Wiring Diagram (*1).” * Do not take power source from this circuit except for LED. 2. Using a toggle switch of 1 pole ON-OFF-ON momentary for DOWN/S1, UP/S2, mounting can be simpler. For Bass Signal Wiring 1. Do not exceed 12 Vp-p for input signal level. 2. Solder uncovered wire (silver) to the earth (ground) of the bass. 3. Solder the white wire to the bass signals. .—w uncovered > earth (ground) of the bass l>— —white > bass signal Black Connect ground 77>Z _0 4: Blue DOWN/S1 О 6: Yellow UP/S2 * In case of above, it is not possible to use simultaneous pressing for DOWN/SI and DOWN/S2 switches. About Transcription for Each Controller When you transcribe each controller into bass itself or owner’s manual, please transcribe as below: GK Volume ...GK VOL Select Switch ...BASS DOWN/S1 Switch ...DOWN/S1 ...MIX UP/S2 Switch ...UP/S2 ...GK Owner's Manual Thank you for purchasing the Roland GK-KIT-BG, a divided pickup kit. The GK-KIT-BG is a specialized kit for internal installation of the included bass divided pickup. Installing the components in the bass allows the bass to be used with GK-compatible devices for bass. Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” These sections provide important information concerning the proper operation of the unit. To ensure proper installation - which is critical - and operation, please read this owner’s manual carefully. The Owner’s manual should be saved and kept on hand as a convenient reference. IMPORTANT NOTES In addition to the items listed under “USING THE UNIT SAFELY, ” please read and observe the following: Roland assumes no liability concerning any damage to the bass and GK-KIT-BG upon installing the GK-KIT-BG. Please proceed with the installation using cation and care at your own risk. Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation. Use a reasonable amount of care when using the unit’s buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions. To avoid the risk of damage to internal components that can be caused by static electricity, please be careful whenever you handle or store the board. To properly drive the GK-compatible device for bass with the GK-KIT-BG, you must adjust the height of the Divided Pickup and the sensitivity of the GK-compatible device for bass. Be sure to make these adjustments correctly, in accordance with this manual and the owner ’s manual for the GK-compatible device for bass. Adjusting the Divided Pickup In the case of basses, the distance between each string differs between instruments, so you will need to adjust the divided pickup according to the dist...