Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
11 [4] OUTPUT'ADJUSTMENT OF THE CONTROLLER UNIT ............................. 14 [5] SPECIFICATIONS .......................................... 15 Please read the separate volume "MIDI", before reading this owner's manual. Copyright © 1986 by ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATOIN. E PANEL DESCRIPTION Guitar Input Connector GM-70 GR-Series < O Normal Guiutar Input Jack © Power Indicator - O Unit Holder — © Divided Pickup ¿) ,rZ21r ....................0:7 MASTER BALANCE CONT1 VOL fcSAIfcHU | ,^|C1 fcdaZISSH-LNAS puepy ~o~o~o~o~o~o- -O Volume Knob -© Balance Knob -© Control Knob 1 -© Control Knob 2 Output Adjusting Knobs 3 © Divided Pickup The Divided Pickup detects the vibration on the guitar. Connect this between the bridge and the pickup. 0 GR Connector Connect the GR Connector to the Guitar Input Connector of the Synthesizer Unit GR-700, 300 or 100 or the GR-MIDI Converter GM-70. Q Unit Holder The Unit Holder is for attaching the Controller Unit to the guitar and also for connecting the Divided Pickup and the Controller Unit. Q Normal Guitar Input Jack Through this jack, normal signal from the guitar is fed into the Controller Unit. Use the supplied normal guitar cord. * Please do not fail to connect to this jack. e Control Knob 1 © Control Knob 2 ► Refer to "Functions of the Control Knobs" on page 12. 0 Output Control Knob ► Refer to "Output Adjustment of the Controller Unit" on page 14. 4 2 INSTALLATION Before installing the GK-1 with the electric guitar, read the following "Important Notes". ■ Important Notes * Please adjust the warp of the neck and the height of the strings of the guitar body before installing the GK-1. * Please try placing the Divided Pickup and the Unit Holder on the guitar to see if they are compatible before actually connecting them. * If the pickup on the guitar is too close to the bridge to connect the Divided Pickup, you need to shift the pickup towards the neck. * Please use the screws for fixing the Unit Holder more securely. Attaching with the adhesive tape may not be sufficient. The adhesive tape may come off with the coating of the guitar. (The supplied both-sided adhesive tape may be used just for experimenting the right position of the Unit Holder.) * If you are left-handed, the following conversion is needed on the Unit Holder. © Remove the cover on the bottom of the Unit Holder. As shown below, loosen and remove the two screws that hold the cover, then insert a driver (for slotted head) between the Unit Holder and the cover, then lift the cover with the driver. @ Move the cord that comes from the pickup to the opposite side. (3) Replace the cover to the Unit Holder. First, check if all the following parts are supplied. Tapping Screw 115mml x8 (For fixing Unit Holder) Tapping Screw [20mm] Pickup Cussion X1 x2 (For fixing Divided Pickup) Tapping Screw [25mml x1 (For fixing End Pin) Pickup Spacer Spring x2 (For adjusting the height of Divided Pickup) Both-sided Adhesive Tape xl xl (For Fixing the Unit Holder) 6 1. Attaching the Unit Holder 0 Pull out the screw to remove the end pin of the guitar. Guitar body. * When using the both-sided adhesive tape for fixing the Unit Holder to the guitar, first, peel the tape and stick it to the Unit Holder, cut unneeded portions, then peel the tape and attach the Unit Holder to the guitar. 0 Bore on the two holes marked with to make holes underneath. The dimeneters of the under holes should be about 2mm (0.08 inches). © Place the Unit Holder on the guitar so that the oval shape hole on the Unit Holder will match the hole where you pulled the end pin. * If your guitar is arched-top type (the one with a round body), the gap between the Holder guitar and the Holder. If this happens, attach the supplied spacer at the relevant place (where the gap is most prominent). (3) Put the End Pin on the oval shape hole on the Unit Holder then insert the screw and tighten it. * If the screw that previously used for holding the end pin is not long enough, use the screw supplied with the GK-1. (D Fix the Holder with the GK-1's supplied screws. The Holder is securely connected in this way, but if you like, you may bore more holes. 7 ■ Installing the Unit Holder to the guitar of unique shape When your guitar is in a unique shape that makes it difficult to install the Unit Holder to, the following convertion will be needed, © Cut off the Unit Holder where the hole for the end pin is bored. (This can be done easily by using the usual saw for metal.) Sever here © Place the Unit Holder on the flat part of the guitar, then fix it with the supplied four screws (15mm). * Before fixing the Unit Holder, please make sure that it does not prevent you from playing the guitar comfortably. Guitar of unique shape. ► Install the Unit Holder flat without using the End Pi...