Оценок - 3, средний балл: 5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
-Ч £> да © £Е 4Q да fi ✓ _3 £ i ш к? м и № W © й ■ м #р öS - M TP ® о КПК ^ НЬ -KJ -5У P V P Р К? 3 fa tí1 ш-ю pJ té I I П P о ■ «fa p í?\ KJ) ¡Si °<4@<й со 5 0 >1 в Jjfci V« р р §1 §)J4P 4^ fa Sfcgvë O tí ШЙ^ ■“ I j DK — ■й Т=Ч и- © 3 р ^ IK Ш к? Р <¿ Jfö J4Q t^E ,u H4~ -О #tí дп t>4v ■+—i (—•> —* я JJL 3? и и; £* ''"" — ^ S Sil â-ЗЩ! MS %^т °2Sg¿ ;\ l-к LL fV ll BJé ±> ni 5100008619-01 Assembling the F-110 Copyright © 2009 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. * To ensure that you assemble the F-110 correctly, please read this manual carefully before you begin assembly. Keep this manual nearby for reference when needed. * Keep the F-110 horizontal when lifting it during assembly or transport. * Be careful not to pinch your hands or drop the F-110 on your foot during assembly or transport. * You must obtain the assistance of at least one additional person when assembling or transporting the F-110. * Keep small parts such as screws, stabilizers, and cord clamps out of the reach of small children to ensure that these items are not swallowed accidentally. * The screwdriver needed for assembly is not included. You' II need to provide a Philips screwdriver (no. 2). * You should initially tighten each screw loosely before tightening them to their final position. Start by tightening the screws until they are approximately half hidden. Do not use a power screwdriver when tightening the screws to their final position. Check the Parts Assembly Procedure 1. Take the side board (right) and side board (left) out of the package, and position the side board packing material together to create a work surface. o 0 0 O 0 O 0 o o F-110 Side board (left) Side board (right) Rear board Pedal board Screws (large): 10 pcs. Screws (small): 6 pcs. Cord clamp: 2 pcs. Stabilizers (left/right) Take the F-110 main unitout of the package, remove the protective mat that surrounds it, and spread the mat out over your work surface. Do not yet remove the protective material that is attached to the left and right of the F-110 main unit. If you remove this protective material and place the F-110 on the floor, protruding parts on the unit may scratch the floor, or the parts themselves may be damaged. 3. Remove the protective material attached to the left and right of the F-110 main unit, and stand it upright on your work surface. * The protective sheet that is wrapped around the F-110 main unit must not be removed until you connect the pedal cord (step 9). Removing the protective sheet before that time will allow the keyboard cover to open, which may be hazardous. 4. Attach the side board (right) and side board (left) to the F-110 5. Attach the rear board to the side boards, and use the large main unit, and use the large screws to fasten them provision- screws to fasten it provisionally, ally. 6. Place the unit upright, and attach the stabilizers to the side boards. * Securely fasten the stabilizers to th...