Оценок - 3, средний балл: 3.7 ( )

Производитель: Roland Размер: 816.38 kb Название файла: Язык инструкции:

As you rotate the knob clockwise, higher frequencies are emphasized, and counterclockwise cuts them. DS-2 TURBO Distortion INSTRUCTIONS Please read the instructions carefully. • The DS-2 is a new type distortion unit that features a newly developed turbo circuits. • All the circuits adopt discrete system, therefore there is very low noise created. • Two types of distortions are optional by changing the Turbo Modes. • The turbo I / II. can be controlled by using the footswitch connected to the Remote Jack. 4-OUTPUT INPUT 4-_ REMOTE 4- TURBO Distortion DS-2 o Output Jack Connect an amplifier to this jack. Q Pedal Switch Pressing the pedal turns on or off the effect. 0 AC Adaptor Jack Connect an AC adaptor (BOSS PSA-120, 220 or 240) to this jack for long and secure operation. Q Turbo Mode Selector Switch This selects the Turbo Mode I or II. (See "OPERATION" for details.) © Distortion Knob This adjusts the depth of the distortion effect. Rotating the knob clockwise deepens the distortion creating powerful distortion effect. Rotating the knob counterclockwise makes lighter distortion. Q Input Jack Connect an electronic musical instrument such as a guitar to this jack. * Plugging in this jack will automatically switch the unit on. Be sure to disconnect the cord from this jack when the unit is not to be used. © Remote Jack By connecting an optional footswitch such as FS-5L to this jack, you select the Turbo Mode I or II using the pedal. * To obtain the above remote controlling function, be sure to set the Turbo Mode Switch to the II (REMOTE) position. Ш. № u> « Мм мал TURBO The most usual distortion sound. Overdrive like sounds with higher frequencies cut off. CONNECTION AC Adaptor BOSS PSA-120/220 or 240 Output 4»output input 4-. REMOTE 4-1 TURBO Distortion , OS-2 Remote Amplifier Bass Guitar Footswitch BOSS FS-5L 0 ( When the unit is not to be used, disconnect the connection cord from the Input Jack, j ■ CAUTIONS • The BOSS manganese battery will last for 10 to 20 hours depending on how you use the unit. • If the battery voltage drops (the Check Indicator lights dimmer), various symptoms are shown, such as the effect becomes weak, no sound is produced, etc. To prevent that, replace the battery immediately. • When the unit is not to be used for a long period of time, remove the battery to prevent problems caused by battery leakage. • Plugging in the Input Jack automatically turns the unit on, so disconnect the cord from the Input Jack when the unit is not in use. • Avoid using this unit in extreme heat or humidity, or where it may be affected by dust. ■ BATTERY REPLACEMENT © Loosen the Screw of Pedal to open it. © Take out the batten/ from the Battery Housing and disconnect the Battery Snap. (3) Replace with a new battery and connect the Battery Snap. * Be sure that the polarity (+/-) is correct © Put the Coil Spring to the Spring Base and close the Pedal. * Make sure that the Battery Snap is not caught in the Pedal or Coil Spring. © Insert the screw into the Guide Bush Hole and firmly tighten the screw. O USE ONE 9-VOLT BATTERY ■ AC ADAPTOR • Be sure to use the AC Adaptor BOSS PSA* 120, 220 or 240 depending on the line voltage system in your country. • Do not use the same socket used for any noise generating or large power consuming device such as a motor, variable lighting system, etc. • Connect the AC adaptor to the AC Adaptor Jack on the unit, then make sure that nothing is connected to the Input Jack, before connecting the power plug to the socket. • Be sure to keep the battery securely connected e...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: