Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Main amp puts out emphasized treble. This two-way system is effective in creating wide-spreading sound and in improving tonal quality. • Pre-out/main-in jack allows you maximum use of any effect unit function. • Headphones jack for monaural or stereo listening. CONNECTING CUBE-60 BASS HEADPHONES (RH-10) Effects Unit To Pre-out Jack To Bi-Amp Jack To Line-out Jack BASS GUITAR irïimÉÜI EXTERNAL AMPLIFIER WITH SPEAKER EXTERNAL AMPLIFIER BASS AMP etc. REAR PANEL BI-AMP JACK MAIN-IN JACK EXT. SPEAKER JACK LINE-OUT JACK PRE-OUT JACK HEADPHONES JACK POWER SWITCH FUSE HOLDER LINE OUT JACK With an additional amp (especially bass amp), power can be boosted. Like pre-out jack, parallel drive is possible. Bl AMP JACK By connecting another amp, bass can be increased. PRE-OUT JACK CUBE-60 BASS can be linked through this jack to line in of another guitar amplifier or to PA mixer. Recording is also possible by connecting to-, tape deck. MAIN-IN JACK An effects unit can be connected between the pre-out jack and this main-in jack. HEADPHONES JACK Connecting headphones to this jack, no sound is produced through the speaker. You can enjoy your playing loud even at midnight. Stereo or monaural headphones can be used. EXTERNAL SPEAKER JACK External speaker system with 8Q or over can be connected and sound can be produced being switched from the combined speaker. This is very effective when souns spread is required. POWER SWITCH Turned to ON, the unit is ready to operate. If noise or hum is heard, reinsert the plug into the wall outlet, reversely. OPERATING CUBE-60 BASS Connect guitar cord plug to HIGH or LOW, depending on guitar output level, and turn on POWER switch. While playing the guitar, set volume and tone controls for desired level. CONTROLS AND FUNCTIONS CONTROL PANEL INPUT JACK VOLUME TREBLE HI MIDDLE BASS PILOT L. LOW INPUT JACK Allows the selection of input level (high or low) according to the guitar output. For normal use, select HIGH. When connecting to a big output bass guitar, select LOW. VOLUME This knob controls volume. Turn clockwise ( O ) to increase and counterclockwise ( O ) to decrease. TREBLE This knob controls high range response. Turn clockwise ( O ) to lift and counterclockwise ( o ) to cut. MIDDLE This knob controls middle range response. Turn clockwise ( O ) to lift and counterclockwise ( O ) to cut. BASS This knob controls low range respc Turn clockwise ( O ) to lift and c terclockwise ( O ) to cut. PILOT LAMP With power switch set to ON, this lights to indicate that the unit is rea operate. CAUTION • If neon or fluorescent lamp is located close to amplifier or instruments, that may cause noise. Separate them from each other. Also, selecting direction of guitar can reduce the noise. • Cube 60 Bass’s speaker produces mid range sound only when a plug is connected to the Bl AMP jack. This jack should not be connected when an additional amp is not needed. When in use, Cube 60 Bass and additional amp must be balanced. The connected amp must have a 60W or more output. • Do not put in or out the power plug with amplifier volume ' set at high level. Speaker is heavily loaded by uncontrolled signals, causing the fear of breaking it. Do it after tuning volume to “0” without fail. • When connecting Instrument and amplifier, connect cord plug to instrument first and then the other end to amplifier. For disconnection, reverse the order: from amplifier first and then from Instrument. • Do not exert big shock upon amplifier. Avoid moving amplifier while it is on. • Avoid using CUBE-60 BASS where there is much dust or under high humidity conditions, which may cause trouble. • If amplifier is soiled, clean with mild cleanser. * Avoid using thinner or the like. • When replacing a fuse, be sure to use that with the specified rating. TROUBLESHOOTING GUIDE If your unit does not operate properly, take proper action be remedied even after the actions instructed, or if there consulting the table below. The symptom listed would be is any symptom other than those listed, make contact caused by mistake in using the unit. If the trouble cannot with the shop you bought your CUBE-60 BASS. SYMPTOM POSSIBLE CAUSE ACTION TO BETAKEN Even when power switch is set ON, pilot lamp does not light and no sound is produced. Imperfect connection of power cord. Fuse blown. Plug in power cord perfectly. Replace. Pilot lamp lights, but no sound produced. Volume is set to minimum. Turn to proper level. SPECIFICATIONS CUBE-60 BASS INSTRUCTIONS Printed in Japan Apr. '84 A-3 Output................. 60Wrms Speaker................................30cm * 1 Input jack............................Hi/Low Control................................Volume/Treble/Middle/Bass Pre-Out jack........................1 Main-lnjack........................1 Line-Out jack......................1 Bi-Amp jack........................1 Headphones jack ........ 1 External speaker jack..........1 ...