Оценок - 5, средний балл: 4.6
(
)
)
|
Фрагмент инструкции
To prevent that, replace the battery a little earlier. AC ADAPTOR (OPTION) BOSS AC A 120 FOR 117V AC BOSS ACA 240 FOR 240V AC •Be sure to keep the battery snapped by connector into the housing, when using AC adaptor, too. *Even if AC Adaptor cord comes out during performance, operations immediately change to battery, causing no trouble in continuing performance. •Power is switched on while a plug is put into input jack. When you do not use the unit keep the plug off the jack. Use BOSS AC adaptor for AC operation. Use of different adaptors may cause improper operation or no sound. BOSS ACA 220 FOR 220V AC SPECIFICATIONS Power Source...................DC 9 V 006P x 1 pc or AC Adaptor Power Consumption.............DC 9 V, 4 mA Controls........................SUSTAIN, LEVEL, ATTACK Others.........................Normal/Effect Changing Switch (FET switching system ) Indicator for battery check Terminal.......................Input, Output, AC Adaptor Maximum Input Level............— 10dBm at 1 kHz Maximum Output Level...........- 10dBm Compression Range..............38dB Input Impedance................1 M 0 (FET Input) Output Load Impedance ..........Over 10 kQ Equivalent Input Noise............- 110dBm (IHF-A) Dimensions.....................70(W) x 55(H) x 125(D) mm Weight.........................400 g "Specifications ore subject to change without notice. OI3DSS Products of Roland Printed In Japan '81 Nov. E-3 CS-2 Compression Sustciiner INSTRUCTIONS •Please read these instructions carefully for proper operating procedures for the BOSS CS-2. I I CAUTIONS FOR REPLACING AND HANDLING BATTERY REPLACING BATTERY USE ONE 9-VOLT BATTERY. OLoosen the screw of pedal to open it and take out battery from its housing. ©Replace the battery by a new one. ©Set coil spring onto the spring base on the back of the pedal and shut the cover (pedal). Finally, insert the screw into the pedal guide and tighten it. At this time, be careful not to catch the battery strap In the cover or coll spring. PEDAL (COVER) C 5^*2.»* a low-noise typo effect providing long sustain with Attack volume. It can adjust picking forth widely and provides any drive-sounds. As having a wide range of Maximum Input Level and Compression, it can be used for any Electronic Musical Instruments. In addition, CS-2 can be used for ordinary Limitter by turning down Sustain Volume. NAME AND FUNCTIONS BATTERY LEVEL «INDICATOR SUSTAIN * AT TACK INPUT JACK rHUMB SCREW BEFORE USING CS-2 "When operating CS-2 from AC line, use * Avoid using CS-2 in dusty location or BOSS AC Adaptor for CS-2 under high tempeiatuie or humidity. CONNECTING CS-2 AMPLIFIER TO BATTERY ELIMINATOR JACK Power is switched on while a plug is BOSSCS-2 put into input jack BOSS AC ADAPTOR LEAD GUITAR BASS GUITAR KEYBOARD (Unplug be used. Be sure to take off connecting plug from Input jack!) this unit when it is not to SUSTAIN 1 he Sustain control provides ndjustmenl of the compression range, when set at the full clockwise position the sustain is the longest. When this control is turned counterclockwise, tho compression increases allowing the unit to limit the out put level. This is particularly useful in adding punch to a guitar, bass and electric piano,. LEVEL This knob determines the amount of sounds. Turn clockwise (! M to increase and counterclokwise to decrease. ATTACK This knob determines the intensity of attack. When this knob is turned clock wise ((>), attack sound to each note will not be lost even in fast picking. INPUT JACK Ihe unit is powered-on by plug-in to the input jack. Keep the plug out of the jack when not In use. OUTPUT JACK The CS-2's low impedance output to the amplifiers is equipped to provide low noise; and hum. BATTERY ELIMINATOR JACK I ho BOSS AC Adaptor is connected to the Battery Eliminator jack when battery operation is not necessarily the most desirable situation INDICATOR By the LED indicator you can see whether the unit is on or off, even in the darkest on-stage situation. This indicator also allows you to check the battery. When the time comes to replace tho battery, the indicator fails to light or becomes dimmer PEDAL SWITCH In our unique FET switching system there are no mechanical contacts in the signal system so it won't make audible click, and it can't make a pop I he switching to tally electronically and therefore, cleanly. THUMB SCREW The battery sits in a special compartment under footswitch plate that activates the silent switch. When the time comes to replace Iho bnttoiy, you don't (»von nood tools "Do not remove off the screw from the unit OPERATING CS-2 After connecting all the cords required, set all the knobs on the panel as illustrated. Press the pedal switch. The Check LED lights to indicate "EFFECT ON" (3nd extinguishes to indicate "EFFECT OFF". ‘This check LED is also used to check battery. If LED fails to light or becomes dim, the battery should be replaced. Turn SUSTAIN co...