Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Should you remove screws, make sure to put them in a safe place out of children's reach, so there is no chance of them being swallowed accidentally. .................................................................................................. IMPORTANT NOTES In addition to the items listed under “USING THE UNIT SAFELY” on page 2–3, please read and observe the following: Placement • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit. • To avoid possible breakdown, do not use the unit in a wet area, such as an area exposed to rain or other moisture. * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. Installation of the CDI-BR-1 • Before installing the CDI-BR-1, you must first always turn off the BR-1180 and unplug the AC adaptor. CAUTION • When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under the four corners or at both ends to prevent damage to the buttons and controls. Also, you should try to orient the unit so no buttons or controls get damaged. • When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over. • Use a Phillips screwdriver that is suitable for the size of the screw (a number 2 screwdriver). If an unsuitable screwdriver is used, the head of the screw may be stripped. • Install only the specified CDI-BR-1. Remove only the specified screws. • Be careful not to cut your hand on the edge of the installation bay. • To avoid the risk of damage to internal components that can be caused by static electricity, please carefully observe the following whenever you handle the CDI-BR-1. • Before you touch the CDI-BR-1, always first grasp a metal object (such as a water pipe), so you are sure that any static electricity you might have been carrying has been discharged. • Before you connect any cables, make sure they do not carry a static electricity charge. Such charges can be transmitted, for example, if the other end of the cable has been in contact with a carpet (or other object) where there is a static electricity buildup. • Never use excessive force when installing a CDI-BR-1. If it doesn't fit properly on the first attempt, remove the board and try again. • When CDI-BR-1 installation is complete, double-check your work. 5 Installation of the CDI-BR-1 1. Turn off the power to the BR-1180 and any connected devices, and disconnect the AC adapter and all other connector cables. 2. Turn the BR-1180 over, remove the screws at the positions shown in the figure, and remove the cover. fig.01 3. Align the CDI-BR-1’s connector with the BR-1180’s socket and insert the connector securely. fig.02 4. Position the CDI-BR-1 as shown in the figure so that the CDI-BR-1’s and BR- 1180’s attachment holes are aligned. fig.03 5. Replace the cover with the positions of the (A) and (B) sections of the cover are reversed relative to their positions prior to the cover’s removal. fig.04 6. Tighten the screws included with the CDIBR- 1 in the positions indicated in the figure (C) until snug, tighten the cover attachment screws until they are snug, and then securely tighten all of the screws. fig.05 7. Turn the BR-1180 back over to its original position. 8. Check the operation of the unit. Place the included CD-ROM in the CDI-BR- 1, then press [LOOP PHRASE IMPORT]. Next, press CURSOR [ ] to select “IMPORT,” then press [ENTER]. If the CDI-BR-1 has been installed correctly, the data on the included CD-ROM is loaded, and the following screen appears. fig.06 * If the screen does not appear, first follow the instructions in “Turning off the power” (p. 30 in the BR-1180 Owner’s Manual) to turn off the unit’s power, then carry out the procedure again starting from Step 1. (A) (B) (B) (A) (C) (C) (C) Installation du CDI-BR-1 • Coupez toujours l'alimentation et debranchez le cable d'alimentation avant d'entreprendre l'installation de la carte CDI-BR-1. PRECAUTION • Utiliser un tournevis cruciforme correspondant a la taille de la vis (un tournevis numero 2). En cas d’utilisation d’un tournevis inapproprie, la tete de la vis pourrait etre endommagee. • Installez uniquement la carte CDI-BR-1 specifiee. Retirez uniquement les vis specifiees. • Veillez a ne pas vous couper les doitgs sur le bord de l’ouverture d’installation. • Veuillez suivre attentivement les instructions suivantes lorsque vous manipulez la carte CDIBR- 1 pour eviter tout risque de dommages aux pieces internes par l'electricite statique. • Touchez toujours un objet metallique (comme un tuyau) avant de manipuler la carte CDI-BR-1, pour vous assurer de vous decharger de toute l'electricite statique que vous auriez pu accumuler. • Avant de connecter tout cable, assurez-vous qu’il ne contient aucune charge d’electricite statique. De telles...