Оценок - 3, средний балл: 4.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Negative (-) settings invert the phase. Acceleration #3 0-15 Adjusts the time over which the Delay Time changes from the current setting to a specified new setting. The rate of change for the Delay Time directly affects the rate of pitch change. HF Damp 200-8000 Hz, BYPASS Adjusts the frequency above which sound fed back to the effect is filtered out. If you do not want to filter out any high frequencies, set this parameter to BYPASS. Pan L64-63R Stereo location of the delay Low Gain -15-+15 dB Gain of the low frequency range High Gain -15-+15 dB Gain of the high frequency range Balance #4 D100:0W-D0:100W Volume balance between the direct sound (D) and the delay sound (W) Level 0-127 Output level 47: TIME SKIP DELAY A delay that changes the delay time in stair-step fashion. Parameter Value Description Delay #1 0-4000 ms, note Adjusts the time until the delay is heard. Skip Rate 0.05-10.0 Hz, note Frequency at which the delay time will change Feedback #2 -98- +98 % Adjusts the amount of the delay sound that's fed back into the effect. Negative (-) settings invert the phase. Acceleration #3 0-15 Adjusts the time oyer which the Delay Time changes from the current setting to its specified new setting. HF Damp 200-8000 Hz, BYPASS Adjusts the frequency above which sound fed back to the effect is filtered out. If you don't want to filter out any high frequencies, set this parameter to BYPASS. Pan L64-63R Stereo location of the delay Low Gain -15-+15 dB Gain of the low frequency range High Gain -15-+15 dB Gain of the high frequency range Balance #4 D100:0W-DO: 100W Volume balance between the direct sound (D) and the delay sound (W) Level 0-127 Output level I 65 About the STEP RESET function 07:STEP FILTER 28 :SLICER The above two types contain a sixteen-step sequencer. For these effect types, you can use multi-effect control ("Multi-effect control (Effects/MFX Ctrl screen)" (p. 29)) to reset the step sequence to its beginning. To do this, set the Control Assign setting for that effect type to "Step Reset." For example, if you want to use the modulation lever to control Step Reset, you would make the following settings. MFX Control-Source: CC01: MODULATION MFX Control-Sens: +63 Control Assign: Step Reset With these settings, the step sequence will be reset to the beginning each time you operate the modulation lever. 66 About Note Some parameters (such as Rate or Delay Time] can be set in terms of a note value instead of a time value. Such parameters provide a Sync switch (Sync SW] that allows you to switch between setting the parameter as a note value or as a numerical value. If you want to set it as a note value, set the Sync SW to ON. * If a parameter that's chosen in Control Assign for multi-effect control has its Sync SW to ON, you won't be able to use multi-effect control to control that parameter. Value Description l/64T(/3) Sixty-fourth-note triplet 1/64| / ) Sixty-fourth note l/32T|Jfe) Thirty-second-note triplet 1/32| ^ ) Thirty-second note l/lôTI/a) Sixteenth-note triplet l/32.( ^ ) Dotted thirty-second note 1/16| J8 ) Sixteenth note 1/8TI Js) Eighth-note triplet 1/16.1 J*. ) Dotted sixteenth note l/8( / ) Eighth note 1/4T(J3) Quarter-note triplet 1/8.1/.) Dotted eighth note 1 /4( J ) Quarter note 1 /2T( d 3 ) Ha if-note triplet 1/4-1 J.) Dotted quarter note l/2(