Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
5 "Clock source Select." VM-7000 setting Set the master clock of the VM-7200/7100 to INTERNAL as follows. 1. Hold down [SHIFT], and press [PROJECT]. 2. Press [DOWN] cursor, then press [F1 (DIGITAL I/O)]. 3. Select "WORD CLOCK SOURCE," and set it to INTERNAL with V1 knob, then press [F1 (SET)] to activate the result. * Refer to VM-C7200/C7100 Owner's Manual p. 32 "Checking the overall system." If AES/EBU device outputs the word clock; Connect the word clock of the AES/EBU device to the VM-7200/7100. Clock Source on the AE-7000 Clock Source on the AE-7000 Clock Source on the AE-7000 Master clock on the VM-7000: R-BUS (9-16): R-BUS (17-24): R-BUS WORD CLOCK If AES/EBU device does not output the word clock; Connect the output of the AES/EBU device to the INPUT A of the 1st AE-7000. In this case, please set the clock source on the AE-7000, and then the master clock on the VM-7000. 1 AE-7000 Supplementary Notes Clock source on the 1st AE-7000: INPUT A Clock source on the 2nd and later AE-7000’s: R-BUS Master clock on the VM-7000: R-BUS which the 1st AE-7000 is connected to * Please refer to AE-7000 Owner's Manual p. 5 "Clock source select" and VM-C7200/C7100 Owner's Manual p. 31 "About Digital Connections and the Master Clock." * If the sys tern of the VM-C7200/C7100 is version 1. Ox, "DIF-AT" is displayed in the R-BUS CONFIG page even though the AE-7000 is connected. This cause no problem for the operation. With the VM-C7200/C7100 version 1.10 or later, you can set the AE-7000 with the R-BUS CONFIG page. If the system software of the VM-C7200/C7100 is version. 1.10 or later; If the system software of the VM-C7200/C7100 is version 1.10 or later, following functions are supported. Clock source setting You can set up the AE-7000's clock source with the VM-C7200/C7100 console. T. Hold down [SHIFT], and press [PROJECT]. SYSTEM menu appears in the display. 2. Select "SYSTEM CONFIG" and go to "R-BUS (1 /2/3)" page. 3. Following page appears in the display. ..... i ...... ....."'"liïiîlïsiŒffli CONNECTION R-BUS 1 U PASE ▼! AE-7000 MENU ICONP'IG iHPUT CH STflTt COPY PROTECT TYPE EMPHASIS SAMPLING RATE JS < A > < B > < C > ___ 77^ '?'>'? 777 TYPE 1 ??? ??? ??? OFF ->^7 77^ 48kHZ UNLOCK UNLOCK UNLOCK CLOCK SOURCE DIGITAL OUT ► f R-BUS MODE Sword clock ►©type i copy OINPUT a ©TYPE 2 protect 4. Select a desired source with V1 [CLOCK SOURCE] knob. 5. Press [F1 (SET)] and the clock source you selected is activated. DIGITAL OUT setting 1. Hold down [SHIFT], and press [PROJECT]. SYSTEM menu appears in the display. 2. Select "SYSTEM CONFIG" and go to "R-BUS (1/2/3)" page. 3. Select the TYPE with V3 [TYPE1/TYPE2] knob. TYPE1: Broadcasfing studio TYPE2: Consumer digital audio 4. Press [F3 (SET)] and the setting is activated. 5. If you set [F4 (COPY PROTECT)] to ON, SCMS turns on and you can restrict the digital copy of the output signal. * If the TYPE is set to TYPE1 (Broadcasting studio), COPY PROTECT setting is invalid. * Digital signal status display If digital signal is connected into the digital input of the AE-7000, status is shown in the middle of the display. How to connect the VM-3100Pro and the AE-7000 Connection Connect the VM-3100Pro and the AE-7000 with the R-BUS cable attached in the AE-7000 box. Booting up AE-7000 works with the power supplied via R-BUS. Turn the power on the VM-3100Pro, and the power is supplied to the AE-7000. Clock source setting If clock source has not been set, noise may be generated from the audio output on the AE-7000 and the VM-3100Pro. While setting the clock source, please turn down the master and monitor level, and turn up again after the setting is finished. Clock source setting varies depending on the AES/EBU devices connected to the AE-7000 and other condition. Please set as follows. 2 AE-7000 Supplementary Notes If AES/EBU device is synchronized to the word clock or the AES/EBU signal from the AE-7000; If AES/EBU input on the AE-7000 is not used, and only output is used; Set the sampling clock of the AE-7000 and the VM-3100Pro as follows. Clock Source on the AE-7000: R-BUS Master clock on the VM-31 OOPro: INTERNAL AE-7000 setting Check if the clock source on the AE-7000 is set to R-BUS. When the AE-7000 is booted up, the clock source is set to R-BUS. If you connect multiple AE-7000, set the clock source on all AE-7000 to R-BUS. * Refer to AE-7000 Owner's Manual p. 5 "Clock source select" VM-31 OOPro setting Set the master clock of the VM-3100Pro to INTERNAL as follows. 1. Hold down [SHIFT], and press [DIGITAL IN]. M.CLOCK SELECT page appears in the display. 2. Press [FI HINT)]. If AES/EBU device is set to the master of the clock; Connect the output of the AES/EBU device to INPUT A on the AE-7000. In this case, please set the clock source on the AE-7000, and then the master clock on the VM-3100Pro. Clock Source on the AE-7000: INPUT A Master clock on the VM-31 OOPro: R-BUS * Please refer to AE-7000 Ow...