Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
ASSIGN” (S. 62) TEMPO “TEMPO ASSIGN” (S. 68) NO ASSIGN “NO ASSIGN” (S. 68) A Copy function is also available. For the procedure, refer to “ASSIGN COPY” (S. 69). * For NOTE, AFTERTOUCH, CONTROL CHANGE, PROGRAM CHANGE, RPN, NRPN, and SYSTEM Ex., the rightmost digit (third place) in the display is a number that indicates the mode (Basic mode or Advanced mode). * If you want to assign a single-byte system message (system realtime message, tune request) or a freely specified message of up to 24 bytes, refer to “SYS EX. ASSIGN” (S. 62). How Basic mode and Advanced mode differ Each assignment can be made either in Basic mode or Advanced mode. Use the mode that is appropriate for your purpose. •Basic mode You can make assignments easily, with the minimum number of steps. •Advanced mode A greater number of steps are required, but you can specify more parameters and make more sophisticated assignments. Edit mode (EDIT) NOTE ASSIGN Here’s how to assign a Note message to a controller. In addition to being used to play sounds, note messages can also be used to control a sequencer. Mode Keyboard Velocity Port Basic mode 0 100 (64H) PCR 1 Advanced mode 1 Assignable Assignable Basic mode 1 Press the [EDIT] button. The display will indicate “EDT”. 2 Slightly move the controller to which you want to assign a Note message. In the case of a button, press that button. The display will indicate the number of the selected controller. 3 Verify that the display shows the correct controller number, and press the [ENTER] button. Press the [NOTE] key. The display will indicate “NT0”. 4 5 Press the [ENTER] button. The display will indicate “C--”. *1 Reference 6 Input the channel. Use the [DEC][INC] buttons or the [0]–[F] keys to specify the channel. 7 Press the [ENTER] button. The display will indicate “N--”. *1 Reference Input the note number. Use the [DEC][INC] buttons or the [0]–[F] keys to specify the note number. 8 9 Press the [ENTER] button. 10 If you are making an assignment for a button, specify the button mode. (.“Specifying the button mode” (S. 80)) *1 The -- area displays the currently set value. If it has not been set, the default setting will be displayed. Even if you change the type or mode of the MIDI message that is assigned, the default setting will be displayed. This will be lit if the value is the same as the currently set value, 49 or will blink if the value is different. Edit mode (EDIT) Advanced mode Advanced mode 1 of NOTE ASSIGN lets you specify the velocity value in addition to the items of Basic mode. 1. Press the [EDIT] button. 2. Slightly move the controller to which you want to assign a Note message. In the case of a button, press that button. The display will indicate the number of the selected controller. 3. Verify that the display indicates the correct controller, and press the [ENTER] button. 4. Press the [NOTE] key and then press key [1]. The display will indicate “NT1”. 5. Press the [ENTER] button. 6. Input the channel. 7. Press the [ENTER] button. 8. Input the note number. 9. Press the [ENTER] button. The display will indicate “V--”. *1 Reference 10. Input the velocity. 11. Press the [ENTER] button. The display will indicate “P--”. *1 Reference 12. Specify the output port. (.“Specifying the port” (S. 81)) 13. If you are making an assignment for a button, specify the button mode. (.“Specifying the button mode” (S. 80)) • If you set [S1--S8], [R1--R8], or [P2] to NOTE ASSIGN, setting the controller to the maximum position will transmit the specified velocity value. Setting the controller to the minimum position will transmit a note message with a velocity of 0. • If you assign this to [B1--B6] or [P1], the specified velocity value will be transmitted when you turn the controller on. When you turn the controller off, a note message with a velocity value of 0 will be transmitted. *1 The -- area displays the currently set value. If it has not been set, the default setting will be displayed. Even if you change the type or mode 50 of the MIDI message that is assigned, the default setting will be displayed. This will be lit if the value is the same as the currently set value, or will blink if the value is different. Edit mode (EDIT) AFTERTOUCH ASSIGN Here’s how to assign an Aftertouch message to a controller. Mode Keyboard Message Value range Port Basic mode 0 Channel Pressure 00–7FH Port 1 Advanced mode 1 1 Channel Pressure Assignable Assignable Advanced mode 2 2 Polyphonic Key Pressure 00–7FH Port 1 Advanced mode 3 3 Polyphonic Key Pressure Assignable Assignable Basic mode 1 Press the [EDIT] button. The display will indicate “EDT”. 2 Slightly move the controller to which you want to assign an Aftertouch message. In the case of a button, press that button. The display will indicate the number of the selected controller. 3 Verify that the display shows the correct controller number, and press the [ENTER] button. Press the [AFTERTOUCH] key. The display will indicate “AT0”. 4 5 Verify that the display is cor...