Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. When powering up: Turn on the power to your guitar amp last. When powering down: Turn off the power to your guitar amp first. *Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. *When operating on battery power only, the unit’s indicator will become dim when battery power gets too low. Replace the battery as soon as possible. *The CHECK indicator shows whether the effect is being applied or not. It does not indicate whether the power to the device is on or not. OPERATING THE UNIT OPERATING THE UNIT 534 1. When you have made the necessary connections, set the knobs as shown in the illustration. 2. Depress the pedal switch to turn the effect on. (Make sure that the CHECK Indicator lights.) 3. Adjust the output balance between the Dry and Overdrive sounds using the BALANCE Knob. 4. Adjust the gain of the Dry or Overdrive sound using the GAIN Knob. 5. Adjust the tone using the HIGH and LOW EQ Knobs. 6. Adjust the LEVEL Knob so there will be no volume difference between the effect and straight bass sounds. CHANGING THE BATTERY CHANGING THE BATTERY Thumbscrew Spring Base Coil Spring Guide Bush Hole Pedal Battery Housing Battery Snap Cord Battery Snap 9V Battery 1.Loosen the thumbscrew at the front of the pedal, then lift the pedal upwards to open the unit. * The thumbscrew can be left in the pedal while changing the battery. 2.Remove the old battery from the battery housing, and remove the snap cord connected to it. 3.Connect the snap cord to the new battery, and place the battery inside the battery housing. * Be sure to carefully observe the battery+s polarity (+ versus -). 4.Slip the coil spring onto the spring base on the back of the pedal, then close the pedal. *Carefully avoid getting the snap cord caught in the coil spring. 5.Finally, insert the thumbscrew into the guide bush hole and fasten it securely. SAMPLE SETTINGS Natural OverDrive Fuzz Sound CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW SAMPLE SETTINGS Natural OverDrive Fuzz Sound CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW Drived Slapping Play Picking Riff CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW Booster HeavyDrive CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW Booster HeavyDrive CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW Slapping Play Solo Play CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW SETTING MEMO CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW CHECK EQLEVEL MIN MAX CUT BOOST DRY OD BALANCE GAIN MIN MAX HIGH LOW SPECIFICATIONS SPECIFICATIONS Nominal Input Level ................. -20 dBu Input Impedance ...................... 1 M. Nominal Output Level .............. -20 dBu Output Impedance ................... 1 k. Equivalent Input Noise Level .... -110 dBu (IHF-A, Typ.) Controls .................................... Pedal Switch LEVEL Knob HIGH EQ Knob LOW EQ Knob BALANCE Knob GAIN Knob Indicator ................................... CHECK Indicator (serves also as battery check indicator) Connectors ............................... INPUT Jack OUTPUT Jack AC Adaptor Jack (DC 9 V) Power Supply ........................... DC 9 V: Dry Battery 9 V type(6F22/9 V), AC Adaptor Current Draw ........................... 15 mA (DC 9 V) *Expected battery life under continuous use : Carbon : 26 hours These figures will vary depending on the actual conditions of use. Dimensions ............................... 73 (W) x 129 (D) x 59 (H) mm 2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches Weight ...................................... 420 g / 15 oz (including battery) Accessories ............................... Owner’s Manual Dry Battery 9 V type (6F22/9 V) Leaflet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,” and “Information”) Options .................................... AC Adaptor PSA-Series *0 dBu = 0.775 V rms *In the interest of product development, the specifications and/or appearance fo this uit are subject to change without prior notice. This product complies with the requirements of European Directive 89/336/EEC. For EU Countries ...