Оценок - 1, средний балл: 5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Also, you should try to orient the unit so no buttons or controls get damaged. When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over. Carefully follow the installation instructions for batteries, and make sure you observe the correct polarity. Avoid using new batteries together with used ones. In addition, avoid mixing different types of batteries. Remove the batteries whenever the unit is to remain unused for an extended period of time. If a battery has leaked, use a soft piece of cloth or paper towel to wipe all remnants of the discharge from the battery compartment. Then install new batteries. To avoid inflammation of the skin, make sure that none of the battery discharge gets onto your hands or skin. Exercise the utmost caution so that none of the discharge gets near your eyes. Immediately rinse the affected area with running water if any of the discharge has entered the eyes. Never keep batteries together with metallic objects such as ballpoint pens, necklaces, hairpins, etc. Expected battery life under continuous use: Carbon: 3 hours, Alkaline: 9 hours These figures will vary depending on the actual conditions of use. When operating on battery power only, the unit's indicator will become dim when battery power gets too low. Replace the battery as soon as possible. We recommend that you keep batteries installed in the unit even when you're powering it with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the AC adaptor gets accidently disconnected from the unit. When connecting, turn down the volume all the way on all equipment! Connect the equipment to the OUTPUT jack. Insert the plug into the INPUT jack to power up the ME-25. Switch on the amp’s power last! If used improperly, batteries may explode or leak and cause damage or injury. In the interest of safety, please read and observe the following precautions. The INPUT jack doubles as the power switch. Power to the unit is turned on when you plug into the INPUT jack; the power is turned off when the cable is unplugged. Insert the included batteries, taking care to orient them correctly. Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. Raise the amp volume only after turning on the power to all connected devices. This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. When connection cables with resistors are used, the volume level of equipment connected to INPUT and AUX IN may be low. If this happens, use connection cables that do not contain resistors. The ME-25 has no built-in amp or speakers. To hear sounds, you’ll need to provide a guitar amplifier, stereo headphones, or other such equipment. For mono output, connect a cable to the L/MONO jack only. If you want to send the output from the PHONES jack to a recorder or other device, use a connection cable such as the PCS-31L (available separately). The PCS-31L has a stereo phone plug on one end, and two phone plugs on the other end. If, instead, you were to use an ordinary guitar cable, only the sound of the L channel would be available in the output. On the ME-25, the level of the signal input via AUX cannot be adjusted. You’ll need to perform that adjustment on the equipment you’ve connected. When needing to monitor the sound being input, first turn down the volume all the way on the device you’ve connected. Then, gradually raise the level until you’ve reached the appropriate volume. 3 Espanol Portugues Nederlands It alia no Francais Deutsch English Let’s Play! Once you’ve finished making the connections, try playing sounds as you operate the ME-25. Switches to the next memory. Switches to the previous memory. DRIVE Knob TONE Knob This adjusts the tone quality of the preamp. VOLUME Knob This adjusts the volume level of the preamp. This adjusts the amount of distortion of preamp distortion. “Phrase Loop Play” (p. 10) This switches to sounds suited to solo performance. Pressing this pedal switches SOLO on and makes the pedal’s indicator light up. Pressing this pedal for two seconds or longer enables the Phrase Loop feature. You can save the settings you've adjusted. “Saving Sounds (Memory Write)” (p. 4) The currently selected sound (memory) and other information appears here. You can use pedal effects to apply wah or a variety of other pedal effects. To assign the pedal’s function, firmly press the toe of the pedal to toggle the PEDAL FX indicator’s status. This lets you get the powerful sound of a large, stack-type tube amp even when you're playing with a small-size ...