Оценок - 2, средний балл: 3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Adjusting the high and low ranges of the overall sound (Equalizer) Use the [LOW] knob to boost or cut the low-frequency range. Use the [HIGH] knob to boost or cut the high-frequency range. English Deutsch Francais Italiano Espanol Portugues Nederlands Example Connections MicrophoneRhythm MachineSound moduleSynthesizer, etc. Musical instrument (Electric acoustic guitar, etc.) Musical instrument (Electric acoustic guitar, etc.) CD player, etc. Portable audio player, etc. RLRLorPCS-31PCS-33RedWhiteFS-5UFS-5LFS-6Foot switchesEffect On/OffMute On/OffEffect On/OffMute On/OffSTEREO LINK OUTMixer, etc. STEREO LINK INSet the FS-5L’s or FS-5U’s polarity switch as shown below. When making the connection using the FS-6, set the POLARITY and MODE switches as shown below. BAOther BA-330 When connection cables with resistors are used, the volume level of equipment connected to the inputs may be low. If this happens, use connection cables that do not contain resistors. 10 Controls and connectors Control panel [MIC/INSTRUMENT] switchSet this to the appropriate position according to whether a microphone or an instrument (a line- output device) is connected to CH1 and CH2. Microphone: Set to “MIC” Instrument: Set to “INSTRUMENT” CH1, CH2 only (monaural)CH3/CH4, CH5/CH6 (stereo) CH3/CH4 and CH5/CH6 are stereo. Connect the following equipmentKeyboardsLine-level devicesGuitarsCD playersPortable audio players, etc. • • • • • CH1, CH2 only[ANTI-FEEDBACK] switchAcoustic feedback will be suppressed if this is “ON.” For more about the anti- feedback function, refer to “Eliminating feedback” (p. 14). Power supply related[BATTERY CHECK/MUTE] switchWhen switched on, the indicator blinks, and sound will no longer be produced from the BA-330’s speakers or from LINE OUT. BATTERY indicatorWhen you press the [CHECK/MUTE] switch, this indicator shows the amount of power re- maining in the batteries. The remaining battery power indication is only an approximation. * Low chargePlease insert new batteries. [OUTPUT POWER] switchIf this is set to “ECO,” the volume from the BA-330’s speakers will be reduced, allowing extended use when run- ning on batteries. [POWER] switchThis turns the BA-330’s power on/off. When this is on, the POWER indicator will light. Full chargeLightBlinkLight outCH1, CH2 (monaural) CH3/CH4, CH5/CH6 (stereo) [TONE] knob[EFFECT] switchCH [VOLUME] knobThis adjusts the tone of the instrument connect- ed to each channel. Turning the knob toward the right makes the tone brighter. Turning this “ON” allows the reverb, delay, or wide effect to be applied to the channel. This adjusts the volume of the device connected to each channel. Turning the knob toward the right increases the volume. The level knobs of unused channels should be set to “0.” * Internal speakers overall[EFFECT] knobThis knob selects the effect type and adjusts its depth for channels whose [EFFECT] switch is “ON.” Effect typeREVERBThis produces the pleasant reverberation that accompanies a performance in a concert hall. DELAYThis produces an echo-like effect by delaying the sound. WIDEThis extends the sound field to the outer edge of the speakers, producing the sensation of be- ing surrounded by sound. EQUALIZERThis lets you adjust the tone by boosting or cutting the low and high ranges inde- pendently. [LOW] knobThis adjusts the low-fre- quency tone. [HIGH] knobThis adjusts the high-fre- quency tone. MASTER [VOLUME] knobThis adjusts the overall volume of the output from the BA-330’s speakers. Controls and connectors English Deutsch Francais Italiano Espanol Portugues Nederlands 11 Jack panel You can place your portable audio player here. This will accommodate a player of up to the following size. * Width: 144 mmDepth: 22 mmInput (INPUT) jacks CH1, CH2: monauralConnect the following equipmentMicrophoneMusical instrument (Guitar, etc.) • • If something is connected to both the XLR connector and phone connector at the same time, the phone jack will be given priority. Wiring diagrams for these jacks are shown below. Make connections after first checking the wiring diagrams of other equipment you intend to connect. TIPRINGSLEEVEHOTCOLDGNDHOTCOLDGNDInput (INPUT) jack CH3/CH4: stereo CH5/CH6: stereoConnect the following equipmentKeyboardsLine-level devicesGuitarCD playerPortable audio player, etc. • • • • • If you’re using a monaural source, connect it to L/MONO (CH4 or CH6). AC adaptor (DC IN) jackConnect the included AC adap- tor here. You can also connect the commercially available cable for an external power device. * Input (AUX IN) jackConnect the following equipmentCD playerPortable audio player, etc. Computer, etc. • • • The RCA phono jacks and mini-jack can be used simultaneously. Use the [LEVEL] knob to adjust the volume. Stereo link (STEREO LINK) jacksThese jacks are used when you want to connect two BA-330 units to create a stereo system with greater output power. For details, refer to “Connecting an addi- tional unit to increase the output (Stereo Link)” (p. ...