Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Symmetric XLR out to connect to e.g. a mixing console. SUBSONIC switch to cut low frequencies from the power amp (CL ND 4: signals below 80 Hz). SPEAKER OUT to connect the amplifier to the speaker. HORN ATT. to control horn volume separately. Retractable handle and wheels make it easy to transport your Warwick Combo. 8 ENGLISH CCL ND 4 FRONT PANEL CONTROLS INPUT socket to plug in a bass guitar. GAIN control + CLIP / LIMIT LED to adjust the input level. LIMITER switch + 2-colored CLIP / LIMIT LED to compress the signal within the preamp. LOW BOOST switch + LED to boost the low end. BASS control to boost / cut low frequencies. PUNCH control for boosting/cutting deep mids. MID FREQ. control to determine the midrange frequency. MID LEVEL control to boost / cut the frequency adjusted with the MID FREQ. control. ATTACK control for boosting/cutting high mids. TREBLE control to boost / cut high frequencies. HIGH BOOST switch + LED to boost the highs. MUTE switch + ON / MUTE LED mutes the signal of all outputs except the PHONES and TUNER socket. To avoid switching noise use the MUTE switch only while no audio signal is being played back. MASTER control determines the main volume level. PHONES socket for connecting headphones (min 200 Ohm). REAR PANEL MAINS IN AC terminal with integrated fuse compartment for connecting the amplifier to mains. POWER switch for turning the amplifier on and off. GROUNDLIFT switch disconnects the protective ground line from signal ground. A humming loop may occur when several devices are hooked up to the same protective ground line and connected by line cables. Use GROUNDLIFT to eliminate humming loops. TUNER OUT to connect to a tuner, active when MUTE is enabled. LINE OUT socket allows connecting additional power amplifiers or active cabinets. EFF. LOOP for the insertion of an effects unit. Connect EFF. SEND with the input and EFF. RETURN with the output of the effects device. DI PRE / POST switch to route the signal to DI OUT socket PRE (pressed, direct signal from the bass) or POST (released, signal affected by equalizer or effects loop). Symmetric XLR out to connect to e.g. a mixing console. SUBSONIC switch to cut low frequencies from the power amp ( CCL ND: signals below 120 Hz). SPEAKER OUT to connect the amplifier to the speaker. HORN ATT. to control horn volume separately. Retractable handle and wheels make it easy to transport your Warwick Combo. 9 ENGLISH CCL ND FRONT PANEL CONTROLS (CCL ND 8 - CCL 210 ND 8) INPUT socket to plug in a bass guitar. GAIN control + CLIP / LIMIT LED to adjust the input level. LIMITER switch + 2-colored CLIP / LIMIT LED to compress the signal within the preamp. LOW BOOST switch + LED to boost the low end. BASS control to boost / cut low frequencies. PUNCH control for boosting/cutting deep mids. MID FREQ. control to determine the midrange frequency. MID LEVEL control to boost / cut the frequency adjusted with the MID FREQ. control. ATTACK control for boosting/cutting high mids. TREBLE control to boost / cut high frequencies. HIGH BOOST switch + LED to boost the highs. MUTE switch + ON / MUTE LED mutes the signal of all outputs except the PHONES and TUNER socket. To avoid switching noise use the MUTE switch only while no audio signal is being played back. MASTER control determines the main volume level. PHONES socket for connecting headphones (min 200 Ohm). REAR PANEL (CCL ND 8 - CCL 210 ND 8) MAINS IN AC terminal with integrated fuse compartment for connecting the amplifier to mains. POWER switch for turning the amplifier on and off. GROUNDLIFT switch disconnects the protective ground line from signal ground. A humming loop may occur when several devices are hooked up to the same protective ground line and connected by line cables. Use GROUNDLIFT to eliminate humming loops. TUNER OUT to connect to a tuner, active when MUTE is enabled. LINE OUT socket allows connecting additional power amplifiers or active cabinets. EFF. LOOP for the insertion of an effects unit. Connect EFF. SEND with the input and EFF. RETURN with the output of the effects device. DI PRE / POST switch to route the signal to DI OUT socket PRE (pressed, direct signal from the bass) or POST (released, signal affected by equalizer or effects loop). Symmetric XLR o...
Эта инструкция также подходит к моделям:Музыкальные инструменты - CCL 210 ND 8 (978.93 kb)
Музыкальные инструменты - CCL ND 4 (978.93 kb)
Музыкальные инструменты - CL ND 4 (978.93 kb)