Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
E1: Motor Drive Error CAUSE: The volume knob has not returned to its assigned position after 20 seconds has elapsed from the start of the recall operation or, the device does not recognize the recall command. SOLUTION: Turn off the power and return the device to the music dealer where you purchased it, or to the nearest Yamaha Service Center for repair. E2: MIDI Receive Buffer Full CAUSE: Too much MIDI data is being received by the DG amplifier at one time. SOLUTION: Try reducing the amount of data being sent or, break the data into smaller blocks. E3: Communication Error. CAUSE: An abnormality is detected during MIDI communications. SOLUTION: Check all connections, etc. and try again. E4: Bulk Receive Check Sum Error. CAUSE: The check sum does not match the received MIDI bulk data. SOLUTION: Check all connections and data, and try again. E5: Bulk Receive Data Abnormality. CAUSE: An abnormality is detected in the received MIDI bulk data. SOLUTION: Check all connections and data, and try again. E6: Backup Battery Error. CAUSE: Backup battery power is depleted. SOLUTION: Continued use of the device will result in the loss of data. Return the device to the music dealer where you purchased it or, the nearest Yamaha Service center and have the battery replaced. Specifications Digital Section Complete Digital Signal Processing Internal 8 Channel Preset Digital Reverb (SPRING/HALL/PLATE) Digital Effects (Tremolo, Chorus, Tape Echo) Speaker Simulator (LINE OUT) Analog Section DG100-212A : 100 W (4 .) Solid State Power Amp 30 cm Speaker (Celestion Vintage 30) x 2 DG80-210A : 80 W (8 .) Solid State Power Amp 25 cm Speaker (V10-60) x 2 DG80-112A : 80 W (8 .) Solid State Power Amp 30 cm Speaker (Celestion G12H100) x 1 DG130HA : 130 W (4 .) Solid State Power Amp MIDI Function Receive : Program change, Control Change (No. 7, 91, 92, 93, 94), Bulk In Transmit : Bulk Out, Merge Out Controller/Switch Front Panel : TRIM, OUTPUT, GAIN (TREMOLO SPEED), MASTER (TREMOLO DEPTH), TREBLE (CHORUS SPEED), HIGH MID (CHORUS DEPTH), LOW MID (CHORUS LEVEL), BASS (TAPE ECHO TIME), PRESENCE (TAPE ECHO FEED BACK), REVERB (TAPE ECHO LEVEL) Rear Panel : LINE OUT volume, EFFECT BLEND Switch : AMP SELECT (LEAD1, LEAD2, DRIVE1, DRIVE2, CRUNCH1, CRUNCH2, CLEAN1, CLEAN2), REVERB, MODE, , , STORE, RECALL Display AMP SELECT display LED x 8 MODE display LED x 3 REVERB type display x 3 7 segment LED x 2 digits Indicator Trim Level Display LED (Green) Trim Clip Display LED (Red) Connection Jacks INPUT HIGH/LOW: Standard Phone Mono Jack SPEAKER (DG100-212A: x 1, DG80-210A: x 2, DG80-112A: x 2, DG130HA: x 2): Standard Phone Mono Jack EFFECT SEND/RETURN: Standard Phone Mono Jack LINE OUT: Cannon Jack MIDI IN, MIDI OUT: 5 pin DIN A/D Converter 20 bit D/A Converter 20 bit Sampling Frequency 48 kHz Memory Number 128 Input Level/Impedance INPUT HIGH: –30 dBm (THRU) / 1 M. INPUT LOW: –20 dBm (THRU) / 1 M. EFFECT RETURN: 0 dBm / 120 k. Output Level/Impedance DG100-212A SPEAKER: 100 W RMS / 4 . LINE OUT: +4 dBm / 600 . EFFECT SEND: 0 dBm / 2.2 k. DG80-210A/DG80-112A SPEAKER: 80 W RMS / 8 ., 100 W RMS / 4 . LINE OUT: +4 dBm / 600 . EFFECT SEND: 0 dBm / 2.2 k. DG130HA SPEAKER: 130 W RMS / 4. LINE OUT: +4 dBm / 600 . EFFECT SEND: 0 dBm / 2.2 k. Power Requirements U.S. and Canadian models : 120 V, 60 Hz General model : 230 V, 50 Hz Power Consumption DG100-212A : 100 W DG80-210A : 100 W DG80-112A : 100 W DG130HA : 140 W Dimensions (W x H x D) DG100-212A : 712 x 574 x 284 mm (28” x 22.6” x 11.2”) w/Caster DG80-210A : 595 x 471 x 284 mm (23.4” x 18.5” x 11.2”) DG80-112A : 542 x 510 x 284 mm (21.3” x 20.1” x 11.2”) DG130HA : 711 x 250 x 284 mm (28” x 9.8” x 11.2”) Weight DG100-212A : 33.5 kg (73 lbs 13 oz) DG80-210A : 26.0 kg (57 lbs 5 oz) DG80-112A : 25.0 kg (55 lbs 2 oz) DG130HA : 18.0 kg (39 lbs 11 oz) * Specifications and design may change without notice. S412V/S112 S412V/S112 2 The S412V is a speaker enclosure equipped with four Celestion “Vintage 30” speakers. * The power rating is 240 W. Use an amp head with a power output of less than 240 W. * The impedance is 8.. Check the amp head’s impedance and make sure it meets the speaker’s requirements. * If you use more than two speakers, make sure the total im- pedance meets the amp head’s requirements. See “Connect- ing Speakers” section on page 8. The S112 is a speaker enclosure equipped with a Celestion “G12H100” speaker. * The power rating is 100 W. Use an amp head with a power output of less than 100 W. * The impedance is 8.. Check the amp head’s impedance and make sure it meets the speaker’s requirements. * If you use more than two speakers, make sure the total im- pedance meets the amp head’s requirements. See “Connect- ing Speakers” section on page 8. Specifications Speakers 30 cm speaker (Celestion “Vintage 30”) x 4 Power Rating 240 W Impedance 8 . Dimensions 765 x 820 x 359 mm (WxHxD) (30.1” x 32.2” x 14.1”) (w/casters) Weight 44.0 kg (97 Ibs) (w/casters) Accessory Speaker Cable Speaker Speaker Size 30 cm (...
Эта инструкция также подходит к моделям:Музыкальные инструменты - S112 (3.51 mb)