Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
If your amplifier stops working and other possible causes have been eliminated (breakers, cords, etc.), have an authorized service center inspect your amplifier for tube failure. TB-1200/600 Block Diagram Tube Replacement Rack Mounting Footswitch The TBFS-4 footswitch allows for remote control of 4 features on the TB–1200/600 amplifiers: OVERDRIVE, VARI.Q™, FX LOOP/BOOST, and TUNER. When the footswitch is connected properly, "On" will be visible in the display. To activate OVERDRIVE, VARI-Q™, or FX LOOP/BOOST, press and release the corresponding button (the LED will turn red indicating the function is active). A volume boost can be achieved by adjusting the TRIM control clockwise (located on the rear of the amplifier, see page 7, item II) and activating the FX LOOP/BOOST button. Note: The front panel buttons on the amplifier may still be used when the footswitch is connected. To activate the TUNER, press and hold the button for about 1 second. The amplifier will be muted (all outputs except TUNER OUTPUT) and the front panel MUTE LED will flash. When a signal is detected, the nearest note is shown in the footswitch display and one of the four red LEDs will flash indicating sharp or flat. The inner two red LEDs indicate the note is closer to being in tune while the green LED in the middle indicates in tune. If a signal is not detected for a few seconds, "---" will be shown in the display. Press and release TUNER button again to exit the tuning function and resume playing. All other footswitch and front panel function buttons have no effect while the tuner is active. Specifications TYPE: PR 693 PART NUMBERS: TB-1200 HEAD: 22-45700-000 (120V, 60Hz) USA, 22-45701-000 (110V, 60Hz) TW, 22-45703-000 (240V, 50Hz) AUS, 22-45704-000 (230V, 50Hz) UK, 22-45705-000 (220V, 50Hz) ARG, 22-45706-000 (230V, 50Hz) EUR, 22-45707-000 (100V, 50Hz) JPN, 22-45709-000 (220V, 60Hz) ROK TB-600 HEAD: 22-45800-000 (120V, 60Hz) USA, 22-45801-000 (110V, 60Hz) TW, 22-45803-000 (240V, 50Hz) AUS, 22-45804-000 (230V, 50Hz) UK, 22-45805-000 (220V, 50Hz) ARG, 22-45806-000 (230V, 50Hz) EUR, 22-45807-000 (100V, 50Hz) JPN, 22-45809-000 (220V, 60Hz) ROK TB-600 COMBO: 22-46000-000 (120V, 60Hz) USA, 22-46001-000 (110V, 60Hz) TW, 22-46003-000 (240V, 50Hz) AUS, 22-46004-000 (230V, 50Hz) UK, 22-46005-000 (220V, 50Hz) ARG, 22-46006-000 (230V, 50Hz) EUR, 22-46007-000 (100V, 50Hz) JPN, 22-46009-000 (220V, 60Hz) ROK POWER REQUIREMENT: 1800W (TB-1200); 900W (TB-600) PRE AMP: INPUT IMPEDANCE: >820k. (Front Panel Input); 10k. (Rear Panel Input) OUTPUT IMPEDANCE: 220. balanced (@ PRE AMP OUTPUT jack) SENSITIVITY: 15mV @ 100/1000Hz for 1.0V RMS at Pre Amp Output (–9dB Pad: out, Volume: 10, Bass: 10, Deep Boost: off, Mid: 10, Treble: 10, Tube Overdrive: disabled, Vari–Q™: disabled, Room Balance: flat, Master Volume: 10, Effects-Trim: 0) TONE CONTROLS: BASS: 10dB range @ 40Hz (Mid: 5, Treble: 5) MID: 15dB range @ 400Hz (Bass: 5, Treble: 5) TREBLE: 9dB range @ 4kHz (Bass: 5, Mid: 5) VARI-Q™ FREQUENCY: 70Hz–2.0kHz VARI-Q™ LEVEL: ±15dB @ Vari-Q™ frequency ROOM BALANCE: ±6.0dB, center frequency: 375Hz BALANCED LINE OUTPUT: IMPEDANCE: 50. MAXIMUM OUTPUT: +26dBu, 600. EFFECTS LOOP: SEND IMPEDANCE: <600. balanced RETURN IMPEDANCE: >10k. balanced NOMINAL LEVEL: -10dBV / +4dBu switchable POWER AMP: INPUT IMPEDANCE: >30k. balanced (@ Power Amp Input Jack) INPUT SENSITIVITY: 1.0V RMS (0dBV) for full power POWER OUTPUT: 1200W RMS into 2. @ 0.2%THD (TB-1200), 1kHz 600W RMS into 4. @ 0.2%THD (TB-600), 1kHz TUBE COMPLEMENT: Two 12AX7WC (0013341000) FOOTSWITCH: TBFS-4 (0070683000) SPEAKER COMPLEMENT (TB-600 COMBO): DRIVERS: 2x10" 16. cast frame, Eminence® HORN: 1 Foster 8. Horn (with attenuator) HORN FUSE: F2A, 250V DIMENSIONS: HEIGHT: 3.5 in (8.9 cm) HEAD; 22.5 in (57.2 cm) COMBO WIDTH: 19.0 in (48.3 cm) HEAD; 23.5 in (59.7 cm) COMBO DEPTH: 15.0 in (38.1 cm) HEAD; 16.5 in (41.9 cm) COMBO WEIGHT: 34 lb (15.4 kg) TB-1200 HEAD; 32 lb (14.5 kg) TB-600 HEAD; 102 lb (46.3 kg) TB-600 COMBO Product specifications are subject to change without notice. fender.com 9 10 fender.com A. INPUT - Conecte aqui su bajo. NOTA: Esta toma anula la entrada INPUT del panel trasero {EE}. B. AMORTIGUACION –9dB - Reduce la sensibilidad de entrada para ofrecer una respuesta mas limpia con bajos de salida alta. Este boton incorpora un piloto rojo que se ilumina cuando esta funcion esta activada. C. MUTE - Desactiva todas las salidas del TB-1200/600 EXCEPTO la salida TUNER OUTPUT {DD} del panel trasero. Este boton incorpora un piloto rojo que parpadea cuando el amplificador esta anulado (mute) o cuando la pedalera esta en el modo TUNER. D. VOLUME - Ajusta el volumen del modulo Vintage Tube Tone (sonido tradicional a valvulas). E. BASS / MID / TREBLE - Sistema clasico de control de tono con solo corte (pasivo). Tire del mando BASS hacia fuera para controlar el enfasis en el rango de los graves (DEEP). Tire hacia fuera del mando TREBLE para producir un aumento del rango de agudos (BRIGHT). El brillo es mas apa...
Эта инструкция также подходит к моделям:Музыкальные инструменты - TB-1200 (13.26 mb)