Оценок - 5, средний балл: 3.8 ( )

Производитель: Behringer Размер: 1.62 mb Название файла: Язык инструкции:

Please take the time to fill in and return the warranty card within 14 days after the date of purchase, so as to benefit from our extended warranty. Or register online at ( You find the serial number of the V-AMP 2 on the base of the casing. [321 FUSE HOLDER/VOLTAGE SELECTOR (V-AMPIRE/ V-AMP PRO only). Before connecting the unit to the mains, make sure that the voltage setting matches your local voltage. A blown fuse should only be replaced by a fuse of the same type and rating. On some units, the fuse holder can be switched to one of two positions, i.e. 230 V and 120 V. When operating the unit outside Europe at 120 V, a higher fuse rating is required (see chapter 8 “INSTALLATION”). [331 The mains connection is on an IEC receptacle (V-AMPIRE/ V-AMP PRO only). An appropriate power cord is included. V-AMP 2: Connect the enclosed power supply unit via the AC IN socket. If it is connected to the mains, your V-AMP 2 will switch on automatically. [341 Connect the stereo jack plug of your FS112V footswitch (included) to the FOOTSWITCH socket (V-AMPIRE/V-AMP 2 only). This will enable you to recall the presets from one bank. To switch on the tuner, hold down the DOWN button on the footswitch for more than two seconds. You can also switch the tuner off again using the same button. [351 The AUX IN jack socket (V-AMPIRE and V-AMP 2 only) enables you to feed in additional stereo signals on the V-AMP 2, to play with a drum computer or playback etc. [361 The AUX LEVEL control (V-AMPIRE and V-AMP 2 only) is used for determining the volume of the signal received at the AUX IN input. [371 These outputs (V-AMPIRE only) are for connecting two external loudspeakers. Without external loudspeakers the internal speaker runs at 70 Watts mono. The left output (the internal speaker automatically shuts off) allows to connect a loudspeaker with 4 Q of impedance and 100 Watts power. At the right output you may connect an 8 Q S0 Watts speaker that runs together with the 2. CONTROL ELEMENTS 7 V-AMPIRE/V-AMP PRO/V-AMP 2 internal speaker. Two speakers with 8 Q/S0 Watts each can be connected to the outputs (the internal speaker automatically shuts off). Our ULTRASTACK BG412 series suits this application ideally. 3. OPERATING MODES AND APPLICATIONS One outstanding feature of our V-AMP products is that you can choose yourself which parts of the signal you want to route to the outputs. To adapt your device perfectly to the various studio and live applications you can choose between S different operating modes (CONFIGURATIONS). Independent of the settings stored in the presets, these operating modes determine where the signal for the line outs and headphones comes from so that both left and right output signal can be used for different purposes. The choice of your most suitable operating mode depends on where you use it. We have described some typical applications, distinguishing between particular features of the V-AMPIRE, V-AMP PRO and V-AMP 2 (see view sheet for details). With the headphones plugged, the device automatically switches into studio 1 (S1) operating mode. 3.1 Selecting an operating mode in CONFIGURATION mode The settings of the configurations are made in the configuration menu by pressing the buttons D and E (B and D for the V-AMP 2). The display shows the current configuration. Use the arrow keys to select another configuration. Please refer to table 3.1 for information on the corresponding output signals. By pressing the TAP key and adjusting the GAIN control you can additionally adapt the input amplification to particularly loud pick ups. In the configuration menu you can adapt the input gain to different pick up types. To do this, keep the TAP key pressed and the surrounding GAIN control LEDs show the current setting. Turning the GAIN control from its center position to the left you will reduce the input amplification which probably is recommendable with very loud pick up types. GAIN settings in clockwise direction are only recommended with very weak pick up types. Quit the configuration menu by pressing TUNER/EXIT. 3.2 Rehearsal or recording at home When using headphones, all three V-AMP models will switch into studio mode 1 (S1). This mode is particularly suitable for rehearsals or when recording/monitoring a stereo signal. You could also use live mode 1 (L1) which applies an additional 3-band EQ. One advantage of rehearsing at home is that there is often a computer available which allows you to design, edit, send, receive and archive new presets comfortably and effectively. Download our V-AMP DESIGN software free of charge at You can create your own presets even with minimum system requirements (Windows PC with MIDI interface or gameport MIDI adapter). On the V-AMP homepage you also find an online preset database (ULI, user library interface) with plenty of presets created by other V-AMP users and famous artists. Here, you can upload your own favourite presets and...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: