Оценок - , средний балл: ( )

Инструкция по эксплуатации Behringer, модель EURODESK SX3242FX

Производитель: Behringer
Размер: 4.75 mb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

(42) Use the TALK TO AUX 1/2 switch to activate the built-in talk- back microphone. Its signal is sent to the AUX SEND jacks 1 and 2. Keep the switch pressed while you’re speaking. (43) This is the built-in talkback microphone. 2.6.2 Phones & control room Fig. 2.18: Phones/control room section (44) The PHONES/CTRL R control adjusts the volume of the headphones connected to the PHONES/CTRL ROOM OUT jack (see (46)). If you have an active monitor speaker or power amp connected here, you can also control the monitor volume. (45) These switches select the signal sent to the PHONES/CTRL ROOM jack. Available sources are: MAIN, CD/TAPE, AUX 1/2 and subgroups 1 - 2 and 3 - 4. Fig. 2.19: Phones/control room output (46) Connect your headphones or monitor speaker to the PHONES/CTRL ROOM OUT 1/4" TRS connector. + IMPORTANT! High volume levels may damage your hearing and/or your headphones/loudspeakers. To avoid switch-on/off thumps from the console and any downstream devices, always make sure that the power amp(s) or active speaker(s) are the last components that are switched on and the first to be switched off. Always make sure that the appropriate volume is set. 2.7 CD/tape Fig. 2.20: CD/tape (47) TO MAIN controls the volume of, for example, a CD player connected to the CD/tape input connectors (see (49)). (48) When the STANDBY switch is pressed, all input channels are muted. Only the CD/tape signal will be routed to the main mix. In this way, you can prevent the microphones from pickung up unwanted sounds or noise that would interfere with CD playback during a break. The main mix and channel faders can remain in their normal positions while playing back music from CD (using the CD/TAPE INPUTs (49)), so you don’t lose your mix. Fig. 2.21: CD/tape connectors (49) The CD/TAPE INPUT RCAconnectors are for the connection of CD players, tape decks or other line-level sources. The signal volume is adjusted with the TO MAIN control. (50) The CD/TAPE OUTPUT RCA connectors provide the stereo main mix signal to a tape deck or DAT recorder to record your mix. The signal is taken pre-fader, so that it will not be influenced by the fader positions. 2.8 Master aux send 1 and 2 Fig. 2.22: Master aux sends (51) These are the master AUX SEND controls 1 and 2 for adjusting the volume level sent to the corresponding aux send connectors (see (52)). This way, you can control the mix of all AUX 1 or AUX 2 signals of the input channels. The AUX SEND section also has a SOLO switch. Control elements and connections 9 EURODESK SX3242FX/SX2442FX 10 Control elements and connections Fig. 2.23: Master aux send outputs (52) Use the AUX SEND outputs 1 and 2 to take the masterAUX SEND signals and route them to an external effects device or your monitor speakers. Subsequently, you can return the effect signal, e.g. via the STEREO FX RETURN inputs (see (67)) or specific input channels. 2.9 Graphic 9-band stereo equalizer Fig. 2.24: The graphic stereo equalizer (53) Your EURODESK is equipped with a graphic 9-band stereo equalizer processing either the main or the AUX 1 signal. Use the EQ to adapt the sound to the room acoustics. (54) Use the EQ IN switch to switch the equalizer on. In this case, the fader LEDs illuminate. (55) With the MAIN/AUX 1 switch you can determine the signal to be processed, either main or AUX 1. (56) Press the FBQ IN switch to activate the FBQ Feedback Detection System. The frequencies causing feedback are indicated by the brightly lit fader LEDs, while all other LEDs are darker. Simply lower the level of the brightly lit faders until feedback disappears. ++ When the switch is in the “AUX 1” position (see (55)), the EQ fader LEDs show both the MAIN and the AUX 1 signal simultaneously. However, if feedback occurs in one of the signals, those signals without feedback will be faded out to enable clear identification of where feedback is occurring. If the MAIN signal happens to be the one carrying feedback, put the switch (55) to “MAIN” and then use the 9-band EQ to remove the feedback. 2.10 Effects section Fig. 2.25: The digital effects processor (57) Here you will find a list of all multi-effects presets (see also chapter 3 “Digital effects processor”). (58) The FX LED level meters show the effects processor’s input signal. Be sure that the clip LED only illuminates with signal peaks. If it is lit all the time, the effects processor is overloading and hence producing unpleasant distortion. (59) The Effect displays show the currently selected presets. (60) This is the master FX 1 (or 2) SEND control for adjusting the volume of all FX send signals at the correspondingFX send jacks (see (66)) and at the inputs of the built-in effects processor. Use it to control the master signal of allFX 1/FX 2 signals from the input channels. When neither of the FX SEND controls is turned up, the effects processor will not receive a signal. (61) Turn the FX 1 (or FX 2) control to select an effects preset. Then, push it briefly to confirm your select...