Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
You must readjust those sources until you get a reading of up to 0 on the VU meters for each. 11. To preset the LINE 3 input source, set LINE 3/LINE 4 to LINE 3. illustration of LINE 3/LINE 4 set to LINE 3 12. Start playback of the selected input source. 13 32-3009.fm Page 14 Tuesday, August 10, 1999 8:31 AM 13. Slowly slide up the CH 3 volume level slide control until you get a reading of up to 0 on both VU meters. illustration ofCH3 control Important: Write down or remember the CH 3 volume level slide control’s setting for the selected audio source, so each time you want to mix that source you can slide the CH 3 volume level slide control to the correct setting. Note: If it was necessary to set the CH 3 volume level slide control all the way to 10 in order to get a reading of up to 0 on the VU meter, then slide CH 3 down to about 8 and rotate MASTER clockwise until you get the reading of 0 on the VU meters. 14. Stop playback of the selected input source. 15. To preset the LINE 4 input source, set LINE 3/LINE 4 to LINE 4. Then repeat Steps 12–14. Note: If you have to readjust MASTER when performing Step 13, remember that this affects the level of the previously preset input sources. You must readjust those sources until you get a reading of up to 0 on the VU meters for each. 14 16. To prevent prematurely mixing audio sources, set all volume level slide controls to 0. Checking the Sound 1. Select one of the input sources, then start playback of the selected source. 2. Set the volume level slide control to the position you determined during presetting. The VU meters should show a reading of up to 0 dB. 3. Turn up the receiver/amplifier’s volume until it reaches the desired level for the location or event where the mixer will be used (this can vary). 4. Adjust BASS, MID, and TREBLE to get the desired sound (see “Using the Tone Controls” on Page 18). Note: If adjusting BASS, MID, and TREBLE causes the VU meters to exceed 0 dB, rotate MASTER counterclockwise until the reading returns to 0. Then adjust your output device (amplifier) volume accordingly. 5. Stop playback of the selected input source. Note: Do not adjust MASTER after checking the sound. 32-3009.fm Page 15 Tuesday, August 10, 1999 8:31 AM MIXING THE INPUTS You can connect input signals from up to six audio sources, select any two, then mix them so only one or both play through your sound system. Mixing requires three operations: • Playing one input source • Monitoring the next input source • Switching to the next input source You can play either of the two selected sources first. Notes: • Ensure the volume level slide control for the other input channel source is set to 0. • The CUE ASSIGN switches are push-on and push-off. You can select more than one at a time. Playing One Input Source 1. Set ASSIGN A to the desired source, then set CROSS FADER to A. illustration ofASSIGN A set to 1 andCROSS FADER set to A 2. Set the input source selector to the preset input source you want to play first through your sound system. illustration 3. Make sure the first input source’s volume level slide control is set to the correct preset position. 4. Start playback of the input source. Monitoring a Second Input Source Monitoring a second input source’s signal level requires selecting the input source that is not currently playing, finding the desired section you want to mix, then adjusting that source’s sound level so it matches the volume level of the source currently playing. 1. Connect and put on headphones. Note: You can listen to one channel through the headphones while the other channel is playing through the sound system. 2. Set ASSIGN B to the second input source. 15 32-3009.fm Page 16 Tuesday, August 10, 1999 8:31 AM 3. Press CUE ASSIGN for the second input source. illustration ofCUE ASSIGN with arrow to CH 2 4. Set the input source selector to the input source you want to monitor. illustration 5. Start playback of the input source you want to play next through your sound system. 6. If necessary: • Adjust CUE LEVEL to a comfortable listening level. • Adjust the second input source volume slide control to the correct preset position. 7. Set the input device to the desired section of music, then stop or pause the input device. Switching to the Second Input Source 1. Start playback of the second input source. 2. When you are ready to play its sound through your sound sys16 tem, slide CROSS FADER from A to B. illustration of CROSS FADER w/arrow from A toB Slide CROSS FADER: • To the left to fade in the channel selected by ASSIGN A and fade out the channel selected by ASSIGN B. • To the right to fade in the channel selected by ASSIGN B and fade out the channel selected by ASSIGN A. • To the center to equally mix the two. Notes on Mixing • If you set CROSS FADER to A to play the channel selected by ASSIGN A, then you must set CUE ASSIGN to CH 1 to monitor CH 1, to CH 2 to monitor CH 2, to CH 3 to monitor CH 3, to CH 4 to monitor CH 4, and to MIC to monitor DJ MIC...
Эта инструкция также подходит к моделям:Музыкальные инструменты - 32-3009 (189.57 kb)