Оценок - 4, средний балл: 4.8
(
)
)
|
Фрагмент инструкции
F R O N T P A N E L 1 5 6 2 3 4 7 8 6 R E A R P A N E L Main Line Out (9) This low-noise‚ electronically-balanced XLR connector can be used to route signals to a mixing console‚ recording device‚ etc. Send/Return Jacks Mains (10 & 11) This pair of 1/4" jacks allow the use of various auxiliary units (effects units‚ equalizers‚ etc.) in-line‚ before the power amp section. Headphone Jack (12) This 1/4" jack accepts stereo headphones only. CH4/Monitor Input Jack (13) Use this 1/4" jack to connect to the output of any line-level device. Channel: 3 Low-Impedance Input (14) For use with low-impedance microphones or other line-level sources equipped with a male XLR connector. Channels 3‚ 2 & 1 (15) These 1/4" jacks accept high-impedance microphones or line-level sources equipped with 1.4" phone plugs. External Speaker Jack (16) (KB3 only) This 1/4" jack provides the powered signal from the amplifier. Use this jack to add a second speaker cabinet in parallel. The external minimum speaker load impedance is 8 ohms. IEC connector/detachable line cord (17) This is a standard IEC power connector. An AC mains cord having the appropriate AC plug and ratings for the intended operating voltage is included in the carton. The mains cord should be connected to the amplifier before connecting to a suitable AC outlet. U.S. Domestic AC Mains Cord The mains cord supplied with the unit is heavy-duty‚ 3-conductor type with a conventional 120 VAC plug with ground pin. Never break off the ground pin on any equipment. It is provided for your safety. If the outlet used does not have a ground pin‚ a suitable grounding adapter should be used and the third wire should be properly grounded. 17 12 9 14 10 11 13 15 16 K KKB BB2 22/ //3 33 B BBl llo ooc cck kk D DDi iia aag ggr rra aam mm 7 K KKB BB® ®®3 33 S SSP PPE EEC CCI IIF FFI IIC CCA AAT TTI IIO OON NNS SS PPRREEAAMMPP SSEECCTTIIOONN The following preamp specs are measured @ 1 kHz‚ nominal signal levels are with channel level controls set at 5‚ minimum levels are with channel level controls set at 10. CChhaannnneell 11 && 22 IInnppuuttss:: Input Impedance: 100k Nominal Input Level: 6 dBV‚ 2 V RMS Minimum Input Level: -10 dBV‚ 316 mV RMS CChhaannnneell 33 IInnppuutt:: Low Z Input Impedance: 10k Ohms Nominal Input Level: -15 dBV‚ 178 mV RMS Minimum Input Level: -33 dBV‚ 22 mV RMS High Z Input Impedance: 75k Nominal Input Level: -15 dBV‚ 178 mV RMS Minimum Input Level: -33 dBV‚ 22 mV RMS CChhaannnneell 44 IInnppuutt:: Input Impedance: 10k Ohms Nominal Input Level: 0 dBV‚ 1 V RMS Minimum Input Level: -25 dBV‚ 56 mV RMS HHeeaaddpphhoonnee OOuuttppuutt Load Impedance: 8 Ohms or greater Nominal Output: 100 mW RMS MMaaiinn LLiinnee OOuutt Output Impedance: <100 Output Level: 18 dBV PPOOWWEERR AAMMPPLLIIFFIIEERR SSEECCTTIIOONN RRaatteedd PPoowweerr && LLooaadd:: 80 W RMS/4 Ohms or 60 W RMS/8 Ohms (1 kHz, 1% THD @ 120 VAC line) FFrreeqquueennccyy RReessppoonnssee:: +0, -1 dB, 20Hz–20 kHz @ 30 W RMS/8 Ohms DDDDTT DDyynnaammiicc RRaannggee:: Greater than 20 dB DDDDTT MMaaxxiimmuumm TTHHDD:: Below 0.5% THD for 6 dB overload Below 1% THD for 20 dB overload HHuumm && NNooiissee:: Greater than 100 dB below rated power PPoowweerr CCoonnssuummppttiioonn:: 120 W @ 120V AC‚ 50/60 Hz‚ Domestic 120 W @ 220–230/240V AC‚ 60 Hz‚ Export K KKB BB® ®®2 22 S SSP PPE EEC CCI IIF FFI IIC CCA AAT TTI IIO OON NNS SS PPRREEAAMMPP SSEECCTTIIOONN The following preamp specs are measured @ 1 kHz‚ nominal signal levels are with channel level controls set at 5‚ minimum levels are with channel level controls set at 10. CChhaannnneell 11 && 22 IInnppuuttss:: Input Impedance: 100 k Nominal Input Level: 1.5 dBV‚ 1.2 V RMS Minimum Input Level: -16 dBV‚ 158 mV RMS CChhaannnneell 33 IInnppuutt:: Low Z Input Impedance: 10 k Ohms Nominal Input Level: -21 dBV‚ 89 mV RMS Minimum Input Level: -38 dBV‚ 13 mV RMS High Z Input Impedance: 75 k Nominal Input Level: -21 dBV‚ 89 mV RMS Minimum Input Level: -38 dBV‚ 13 mV RMS CChhaannnneell 44 IInnppuutt:: Input Impedance: 10 k Ohms Nominal Input Level: 0 dBV‚ 1 V RMS Minimum Input Level: -25 dBV‚ 56 mV RMS HHeeaaddpphhoonnee OOuuttppuutt Load Impedance: 8 Ohms or greater Nominal Output: 100 mW RMS MMaaiinn LLiinnee OOuutt Output Impedance: <100 Output Level: 18 dBV PPOOWWEERR AAMMPPLLIIFFIIEERR SSEECCTTIIOONN RRaatteedd PPoowweerr && LLooaadd:: 45 W RMS/8 Ohms/low channel 12 W RMS/8 Ohms/high channel (1 kHz, 1% THD @ 120 VAC line) DDDDTT DDyynnaammiicc RRaannggee:: Greater than 20 dB DDDDTT MMaaxxiimmuumm TTHHDD:: Below 0.5% THD for 6 dB overload Below 1% THD for 20 dB overload HHuumm && NNooiissee:: Greater than 90 dB below rated power PPoowweerr CCoonnssuummppttiioonn:: 150 W @ 120V AC‚ 50/60 Hz‚ Domestic 150 W @ 220–230/240V AC‚ 60 Hz‚ Export CCrroossssoovveerr:: Fixed‚ 18 dB/octave‚ 3.5 kHz crossover frequency 8 K KKB BB® ®®2 22/ //K KKB BB3 33 EESSPPAANNOOLL Amplificadores para Teclados Gracias ...
Эта инструкция также подходит к моделям:Музыкальные инструменты - KB2 (1.61 mb)
Музыкальные инструменты - KB3 (1.61 mb)
Музыкальные инструменты - KB2 (1.61 mb)