Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
If both inputs are used simultaneously, the output levels are the same (both are Low Gain). CLEAN GAIN (3) Controls the channel volume. BRIGHT SWITCH (4) Provides a preset boost to treble frequencies. To activate, depress the switch to its “in” position. The bright function affects only the clean channel. CHANNEL SELECT SWITCH (5) Allows selection of the Ultra or Clean channel and the “out” position selects Clean. NOTE: Channel selection may also be accomplished by the remote footswitch. If remote selection is desired, the channel switch must be in the “in” (Ultra) position. LOW, MID, & HIGH EQ (6) Passive tone controls that regulate the low, mid and high frequencies, respectively. PRE GAIN (7) Controls the input volume level of the channel. POST GAIN (8) Controls the overall volume level of the channel. The final level adjustment should be made after the desired sound has been achieved. ULTRA GAIN SWITCH (9) Boosts the overall system gain of the Ultra channel. Depress to the “in” position to activate. CRUNCH GAIN SWITCH (10) Boosts the overall system gain of the Crunch channel. Depress to the “in” position to activate. PRE GAIN (11) Controls the input volume level of the channel. POST GAIN (12) Controls the overall volume level of the channel. The final level adjustment should be made after the desired sound has been achieved. BOTTOM (13) An active tone control (shelving type ±15 dB) that varies the low frequency boost or cut. NOTE: This control is not functional on the Clean channel. BODY (14) An active tone control (peak/notch, ±15dB) that varies the mid frequency boost or cut. NOTE: This control is not fuctional on the Clean channel. EDGE (15) An active tone control (shelving type, ±15 dB) that varies the high frequency boost or cut. NOTE: This control is not functional on the Clean channel. REVERB LEVEL (16) Reverberation is an echo effect. Rotate clockwise to increase the effect. Remote footswitch can control On/Off. MASTER LEVEL (17) Controls the overall volume level of the system. Once a desired balance of the Clean, Crunch, and Ultra channels is achieved, the entire system level may be increased or decreased with the Master Level Control. STATUS LED (18) Illuminates when amp is switched to standby indicating amplifier is not operational. POWER LED (19) Illuminates when AC power is being supplied to the amp. STANDBY SWITCH (20) Allows amp to be placed in standby or active mode. In standby mode the tubes remain hot, but the amplifier is not operational. POWER SWITCH (21) Depress the switch to the “On” position. The red pilot light (LED) will illuminate indicating power is being supplied to the unit. BACK PANEL A A CAUTION RISK Oh tri К [Rif c;HCCK DC NOT OPf.N I AVIS: RISQUE DE CHOC I ELECTRIQUE - NE PAS OUVRIR. | EFFECTS PREAMP 120 VAC SEND RETURN OUT REMOTE SWITCH 60 Hz 200 WATTS SPEAKER OUTPUTS MAIN AUX 8 OHMS 4 OHMS 60 W RMS/22 V RMS GROUND SWITCH (22) Three position rocker-type switch which, in most applications, should be operated in its center or zero position. There may be some situations when audible hum and/or noise will come from the loudspeaker. If this situation arises, position the ground switch to either positive or negative ( + or -) or until the noise is minimized. NOTE: Should the noise problem continue, consult your Authorized Peavey Dealer, the Peavey Factory, or a qualified service technician. THE GROUND SWITCH IS NOT FUNCTIONAL ON 220/240 VOLT MODELS. EFFECTS SEND (23) Output for supplying signals to external effects or signal processing equipment. EFFECTS RETURN (24) Input for returning signals from external low-level effects or signal processing equipment. PREAMP OUT (25) The preamp output can be used to route the amplified signal to a mixing console, tape recorder, etc. Connect the preamp output using a shielded cable to an input of the tape recorder, mixer, etc. This patch does not affect the operation of the amplifier. FOOTSWITCH JACK (26) Provided for the connection of the supplied remote footswitch. Footswitch switch is used to select the Ultra Gain, Crunch Gain, or Normal channels and...
Эта инструкция также подходит к моделям:Музыкальные инструменты - Triumph PAG 120 (1.02 mb)
Музыкальные инструменты - Triumph PAG 60 (1.02 mb)
Музыкальные инструменты - Triumph PAG 120 (1.02 mb)