Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
7: TREBLE: Adjusts the high frequency output level: to the left reduces the high frequency output; to the right increases it. 8: INSERT: Connect an external effects device via this jack. Use a stereo 1/4” male Y- cord: ring = send, tip = return, sleeve = ground. Send goes to the effect’s input; return comes from its output. (See the illustration on the panel to the right for more information.) 9: HEADPHONE: Plug a pair of stereo headphones here for private listening. When this jack is used the internal speakers and the external speaker jacks are disconnected. 10: POWER LED: This LED lights when the amplifier is powered up. 11: POWER SWITCH: Turns the amplifier on (in the UP position) and off (in the down position). 12: AC LINE IN: (Rear panel, not shown) This heavy-duty, grounded, three-wire power cord is to be plugged into ONLY a safely-wired, grounded 120 volt, 60 cycle AC power outlet. DO NOT attempt to defeat the ground connection of this cable! If your EL10G was purchased outside of the United States, see the unit’s rear panel for its power rating and follow the above guidelines. EL-10G Electra Series Guitar Amplifier EL-10G Electra Series Guitar Amplifier 7 8 910 11 Getting Your Sound: The Boost, Gain and Volume controls (#2, 3 & 4) can be used together to obtain a wide variety of sounds. Experimenting with the following guidelines will help you get the sound you’re looking for. Clean Sounds: Keep the Gain control “off” (the Boost control will be inactive). Use the Volume control to set the output level. “Crunch” Sounds: Set the Boost control around “4”, turn the Gain on and set it to “2”. Use the Volume control to set the output level. (A lower setting of the Volume control is needed as the Boost and Gain controls are increased.) Rhythm Distortion: Set the Boost control around “4”, Gain at or near “10”. Use the Volume control to set the output level. Lead Distortion: Set the Boost and Gain controls at or near “10”. Use the Volume control to set the output level. Connecting to the Insert jack: The Insert jack (#8) lets you patch external effects into the amplifier just prior to its power amp stage. Use Crate’s STP201, STP202 or STP203 stereo-to-mono Y-cord or an adapter such as Crate’s YPP117 and 2 1/4” mono signal cables to connect to the effect as shown: Stereo-to-mono Y-cord: Y-adapter and 2 cables: TIPRINGSLEEVE to Insert jack(STP201, 3' STP202, 6' STP203, 9') to effect "OUT" jack toeffect"IN" jack RINGTIP RETURN SEND GROUND to to effect effect "OUT" "IN" jack jack External Effect External Effect to Insert jack (YPP117) TIP RING SLEEVE RINGTIP (1/4"-TO-1/4" MONO CABLES) INPUT Gain Volume Treble Mid Bass B+ B– Overdrive POWER SW POWER LED OVERDRIVE POWER SUPPLYAC POWER BUFFER PRE AMP POWER AMP EQUALIZATION SPEAKER INSERT TIP: RETURN RING: SEND HEADPHONE Block Diagram: EL-10G Electra Series Guitar Amplifier EL-10G Electra Series Guitar Amplifier EL10G TECHNICAL SPECIFICATIONS Output Power Rating 10 watts @ 1% THD 14 watts @ 10% THD Speaker Size 6” Input Impedance 500k ohms Minimum Noise 1mV Maximum Noise 10mV Distortion 0.9% Input Power Requirements 120 VAC, 60Hz, 20VA 100/115VAC, 50/60Hz, 20VA 230VAC, 50/60Hz, 20VA Cabinet Size and Weight 14” H x 12-1/2” W x 6” D, 12 lbs. The EL-10G is covered with a black Tolex material: wipe it clean with a lint-free cloth. Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which could damage the finish. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION RISQUE D'ELECTROCUTION NE PAS OUVRIR ATTENTION: POUR REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST...
Эта инструкция также подходит к моделям:Музыкальные инструменты - ELECTRA SERIES EL-10G (101.52 kb)