Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
1) Remove the platter from its protective wrapping and place on the spindle of the main unit. 2) Loop the belt over the motor pulley. Be sure it does not twist. 3) Remove the slipmat from its protective wrapping and place on the platter. 4) Place the counter-weight on the back of the tonearm assembly. 5) If desired place the 45rpm adaptor in its allocated holder on the main unit. - Do not place the unit in a location where it will be exposed to direct sunlight or near a heating appliance. - Do not place the unit in a location where there is high humidity or a lot of dust. - Cartridge may pick up slight sound pressures or vibrations from the speakers coming along the floor or through the air resulting in feedback. Find a location which is very stable and vibration free. - The legs have functions for adjusting the height of the unit itself. Adjust the legs to stabilize the main body horizontally. T.52 ASSEMBLY T.52 CONNECTIONS T.52 PLACEMENT Driving roller Drive belt To properly connect your T.52, please follow these simple instructions: 1. Turn Off your equipment. 2. Connect the power cord to an AC outlet. 3. Connect the RCA cable from the T.52 Phono Output to your DJ Mixer Phono Input. 4. Connect the ground cable from the T.52 ground post to your DJ Mixer ground terminal. 8 T.52 TONEARM AND CARTRIDGE SETTING T.52 TONEARM AND CARTRIDGE SETTING The major cause of problems in sound and skipping on the vinyl is the lack of proper set up of the needle and turntable adjustments. The needle is designed to operate at a specific angle to the vinyl. The T.52 has two adjustments to correctly position the needle to the vinyl. 1. The first adjustment is the installation of the cartridge-head-shell assembly into the tone arm tube lock. The T.52 includes a Stanton 500 V3 cartridge pre-mounted to the headshell. Holding the tone arm tube in one hand, insert the cartridge-headshell into the tube lock with the other hand. Turn the lock ring clockwise (when viewed from the rear) until the headshell is locked tightly into the tone arm. Remove the needle protector from the cartridge and place the needle on record. View the needle from the front and insure that the needle is perpendicular to the record surface. If some adjustment is needed, simply loosen the lock ring and rotate the cartridge headshell until the needle is perpendicular to the record surface. Then re-tighten the lock ring. 2. The second adjustment is the needle (or stylus) pressure. Start with the cartridgeheadshell assembly mounted into the tone arm. Remove any needle protectors provided. With tone arm free, adjust the tone arm counterweight by rotating the rear section until the tone arm floats in a balanced condition above the record or mat. Do not allow the needle to drop onto the mat or the turntable platter during this adjustment. You might damage the needle tip. Now, carefully hold the tone arm in one hand while rotating the numbered ring on the front of the counter-weight with the other hand to the “0” setting. Next, without touching the numbered ring, Rotate the rear counterweight until the desired needle pressure reading is next to the line on top of the tone arm tube. The recommended stylus pressure for the Stanton 500 V3 cartridge is between two and five grams. Locking Ring 1 2.0 1.0 0 Rear Section Numbered Ring 2 T.52 OPERATIONS 1. Rotate the power dial clockwise to turn on the power, the speed indicator and the strobe-illuminator will light up. 2. Place a record on the slip mat, when playing a 45rpm record with a large center hole, place the 45-rpm adaptor on the center spindle. 3. Set the rotation speed (33/45) to match the record. 4. Remove the stylus protector, release the arm clamp. 5. Press the Start/Stop button, the turntable platter will start to rotate. 6. Move the tonearm over the desired groove. 7. When play is finished, move the tonearm to the arm rest, secure the tonearm with the arm clamp. 8. Press the Start/Stop button to stop the platter rotating, rotate the power dial to turn off the power T.52 MAINTENANCE - For best results & proper care of your equipment use Stanton Vinyl Cleaner (VC-1) for your records and Stylus Cleaner Kit for styli (SC-4). - Clean the stylus periodically with a soft brush to prevent the accumulation of dust. - When the sound becomes distorted or noisy, check the stylus. If worn out, replace it with a new one. -Any volatile materials such as alcohol, thinner, benzine, etc., may remove the paint or damage the paint finish, please avoid. 9 1. Start/Stop - Press this button to start or stop the platter. 2. Strobe dots - The dots around the edge of the platter are used in conjunction with the light located inside the motor ON/OFF switch. While the platter is in rotation, the dots help to indicate the speed of rotation. The speed is lower than the displayed speed (33,45,) when the dots are flowing to the right. It is higher than the displayed speed (33,45,) when the dots are flowing to the left. When the strobe is sto...