Оценок - 4, средний балл: 4.3 ( )

Производитель: Marshall Amplification Размер: 340.01 kb Название файла: Язык инструкции:

These can then be recalled when using the unit in Preset mode. When channel settings have been stored the current channel light (3 or 5) will stop flashing indicating the preset has been saved. Reverb & FX The amplifier provides two simultaneous effects, Reverb and one of four FXs (Chorus, Phaser, Flanger or Delay) Reverb The Reverb control (8) sets the amount of signal sent to the reverb section - allowing the reverb to spill between channels as different presets are recalled. When the Reverb control (8) is set to ‘0’ the reverb is switched off, the status of the reverb is also indicated on the optional footcontroller. FX The FX control is split into four segments and selects the type of FX and adjusts its associated settings. When the FX control is set to ‘0’ the FX are switched off, the status of the FX is also indicated on the optional footcontroller. 0 FX Off Chorus Speed increases and depth is reduced as knob is turned clockwise. Phaser Speed increases as knob is turned clockwise. Flanger Speed increases, feedback and depth are reduced as knob is turned clockwise. Delay Delay level is increased as knob turned clockwise. Tap Tempo The Tap Tempo switch (10) is used for the Delay effect only. The Tap Tempo switch matches the delay time to the time between two presses. The Tap Tempo LED flashes red at the selected/recalled delay time. The number of repeats is reduced as the delay time decreases. If you change from a channel with delay to one without delay the effect will spill between channels. If you change from a channel with delay to a channel with delay set to a different delay time the delay effect will not spill between channels. MP3 /Line In The 3.5mm MP3 / Line In socket (14) allows the connection of an external audio source e.g. MP3 or CD player. Headphones The 3.5mm Headphones socket (16) allows the connection of a pair of headphones. When a jack is inserted into the headphones socket the unit’s speaker is muted. Power The Power switch (17) turns the amplifier on and off. If current settings have not been stored they will be lost. 2 Restoring Settings - WARNING ALL AMP & FOOTCONTROLLER SETTINGS WILL BE LOST To restore the unit to factory settings (see handbook rear cover) you must hold the Store switch (12) while powering on the unit. The Clean/Crunch (3) and OD (5) lights will light orange. You can then release the Store switch (12). Resetting the amplifier will erase all user Channel presets and all user Footcontroller settings, replacing them with the factory presets. MG15FX Technical Specification Power (RMS) 15W Channels 4 Speaker 1x8" Weight (kg) 7.7kg Size (mm) W, H, D 382 x379 x205 MG30FX Technical Specification Power (RMS) 30W Channels 4 Speaker 1x10" Weight (kg) 10.8kg Size (mm) W, H, D 480 x420 x225 * EUROPE ONLY V V - Note: This equipment has been tested and found to comply with the requirements of the EMC Directive (Environments E1, E2 and E3 EN 55103-1/2) and the Low Voltage Directive in the E.U. * EUROPE ONLY - Note: The Peak Inrush current for the MG15FX is 2.5 amps. The Peak Inrush current for the MG30FX is 5 amps. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and the receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help. Follow all instructions and heed all warnings KEEP THESE INSTRUCTIONS ! 3 MG50FX / MG100FX Technical Specifications MG50FX Combo 21 1. Input Jack Socket Jack input for your guitar. Use a good quality guitar cable (i.e. one that's screened/shielded) to help prevent noise, interference and unwanted feedback. 2. Gain Control Controls the amount of signal entering the pre-amp and the amount ofdistortion created in the selected channel. 3. Clean : Crunch Switch Selects between Clean (green) and Crunch (red) channels. 4. Bass Control Adds warmth and low-end depth to your sound. 5. OD Switch Selects between OD1 (green) and OD2 (red) channels. 6. Middle Control Varies the amount of body in your sound. 7. Treble Control Increasing the Treble wil...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: