Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
To avoid the risk of electrical shock, do not place fingers or any other objects into empty tube sockets while power is being supplied to unit. HEADPHONE JACK (Envoy 110 ONLY) This stereo 1/4” jack accepts a standard pair of headphones. Using this jack defeats the output to the speaker making it ideal for quiet practice applications. SPEAKER SIMULATED DIRECT OUTPUT The signal produced in this convenient 1/4" direct output jack is specifically voiced to accurately simulate speaker cabinet response. The output can be used for direct recordings or sent to a mixer or PA system. Users can adjust output levels with the adjacent control knob (Bandit 112 Only). 16 17 POWER LEVEL (Bandit 112 ONLY) This switch provides three power level options: 25%, 50% and 100%. This circuit is actually a patented tube power amplifier simulator that "squashes" the signal. Use as desired for different playing environments, for example an apartment at 25% or live big at 100%. EXTERNAL SPEAKER JACK (Bandit 112 ONLY) This 1/4” jack is provided for the connection of an external speaker cabinet. The minimum external speaker impedance is 8 ohms. DAMPING (Bandit 112 ONLY) This three position switch offers damping level adjustment; loose, medium and tight. EFFECTS LOOP (Bandit 112 ONLY) This pair of mono 1/4” jacks provides an effects SEND and RETURN path for the preamp signal. Connect the SEND jack to the input of an external, low-level, signal processing effects unit. Return the signal from your external effects unit to the RETURN jack. This setup is known as an Effects Loop since the signal exits your amp (send) and loops (return) back to it. REMOTE SWITCH The multi-functional remote footswitch is used to select between the Clean and Lead channels as well as to boost the volume. NOTE: On both units, the Channel Select Switch (6) must be in the LEAD position for the Remote Switch to work. Rear Panel 22 18 22 20 19 21 18 19 20 21 22 Suggested Settings Clean/MetalJazz/Moderate DistortionClean Blues/Dirty Blues Clean Metal Clean Channel: Volume: As Desired Classic Low: 7-9 Mid: 2-4 High: 5-7 Lead Channel: Pre Gain: 8-10 High Gain/ModerateClassic: Moderate Low: 8-10 Mid: 0-2 High: 6-8 Post Gain: As Desired Master Section: Reverb: As Desired Boost: As Desired for solo level Clean/MetalJazz/Moderate DistortionClean Blues/Dirty Blues Jazz Moderate Distortion Clean/MetalJazz/Moderate DistortionClean Blues/Dirty Blues Clean Channel: Volume: As Desired Classic Low: 7-9 Mid: 6-8 High: 3-4 Lead Channel: Pre Gain: 3-5 High Gain/ModerateClassic: High Low:7-9 Mid: 4-6 High: 5-7 Post Gain: As Desired Master Section: Reverb: As Desired Boost: As Desired for solo level Clean Blues Dirty Blues Clean Channel: Volume: 8-10 Classic Low: 5-7 Mid: 7-9 High: 3-5 Lead Channel: Pre Gain: 3-5 High Gain/ModerateClassic: Classic Low: 5-7 Mid: 7-9 High: 2-4 Post Gain: As Desired Master Section: Reverb: As Desired Boost: As Desired for solo level NOTE: The Bandit 112 is used for demonstration purposes. The settings illustrated above are also applicable to the Envoy 110. 12 Series Specifications Envoy® 110 Power Amplifier Section: Power @ Clipping (Typically): (1 kHz, 120 VAC line) 40 W RMS into 6 . Frequency Response: +0, -2 dB 100 Hz to 20 kHz @ 35 W RMS into 6 . Hum and Noise: Greater than 86 dB below rated power Power Consumption: (Domestic) 75 W @ 60 Hz, 120 VAC (Export) 75 W @ 50/60 Hz, 220-240 VAC Preamp Section: The following spec are measured @ 1 kHz with the controls preset as follows: Clean Mode Switch, Classic Lead Mode Switch, Classic Low and High @ 10 Mid @ 0 Lead Pre and Post Gain @10 Lead Mode Switch, Vintage Reverb @ 0 Nominal Levels are with Clean Volume @ 5 Minimum Levels are with Clean Volume @ 10 Headphone Output: Load Impedance: 16 . or greater 0.3 W RMS System Hum & Noise @ Nominal Input Level: (20 Hz to 20 kHz unweighted) Greater than 78 dB below rated power Speaker Simulated Direct Output Level: 0.4 V RMS Nominal Equalization: Special Low, Mid, and High passive type EQ. Vintage/Classic/Warm switch (clean) Three distinct EQ voicings Classic/Modern/High gain switch (lead) Three different EQ and Gain voicings External Footswitch Functions: Clean or Lead channel selection and volume Boost Dimensions (H x W x D): 17" x 19.375" x 9.250" 43.18 cm x 49.21 cm x 23.46 cm Weight: 24.5 lbs (11.13 kg) Features and specifications subject to change without notice. Series Specifications Bandit® 112 Power Amplifier Section: Rated Power and Load: Power specs measured with Power Level @ 100% 80 W RMS into 8 . 100 W RMS into 4 . Power @ Clipping (Typically): (1 kHz, 120 VAC line) 80 W RMS into 8 . 100 W RMS into 4 . Frequency Response: +0, -3 dB 100 Hz to 20 kHz @ 65 W RMS into 8 . Hum and Noise: Greater than 90 dB below rated power Power Consumption: (Domestic) 300 W @ 60 Hz, 120 VAC (Export) 300 W @ 50/60 Hz, 220-230 VAC Effects Send: Load Impedance: 1 k . or greater Nominal Output Level: -5.4 dBV, 535 mV RMS Effects Return: Load Impedance: High Z, 22 k . Designed...
Эта инструкция также подходит к моделям:Музыкальные инструменты - ENVOY 112 (2.88 mb)