Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
The “0” position is maximum cut; the “10” position is maximum boost. Front Panel 1 2 3 4 5 7 8 9 10 11 12 13 14 15 6 ( ((1 110 00) ))P PPO OOS SST TT G GGA AAI IIN NN This control sets the overall gain of the Lead channel. ( ((1 111 11) ))C CCH HHA AAN NNN NNE EEL LL S SSE EEL LLE EEC CCT TT This switch selects the channel (Lead or Clean). The ACTIVE CHANNEL LEDs (6) indicate the active channel — green for Clean; red for Lead. ( ((1 112 22) ))E EEF FFX XX A AAD DDJ JJU UUS SST TT Pressing this control selects the effect. A yellow LED adjacent to the effect name will illuminate to indicate the selected effect. Rotating this control clockwise changes the parameter of the active effect according to the descriptions below. The surrounding LED ring indicates relative value of the parameter being adjusted. EFX ADJ PARAMETERS Tremolo -Rate increase Funk Wah -Sensitivity increase Octaver - Wet/Dry mix Rotary Speaker -Rate increase Flanger -Rate increase Phaser -Rate increase Chorus -Rate increase/depth decrease EFX amps are built with factory settings loaded into the presets. To return to the factory settings, press and hold both the EFX ADJUST (12) and DELAY (14) controls while turning the amp on. ( ((1 113 33) ))R RRE EEV VVE EER RRB BB This control adjusts the overall reverb level. The surrounding LED ring indicates level. ( ((1 114 44) ))D DDE EEL LLA AAY YY This control adjusts delay type, time, and volume. Three types of delay are available: SLAP (1 repeat), ECHO (3-4 repeats), or INFINITE (5-6 repeats). The LEDs in each section of the control indicate which type is active and volume level. Pressing the control twice sets the delay time to the interval between presses. ( ((1 115 55) ))P PPO OOW WWE EER RR S SSW WWI IIT TTC CCH HH This switch applies power to the unit in the “ON” position. One of the ACTIVE CHANNEL LEDs (6) will illuminate to indicate that the unit is on. Pressing the lower portion of the switch turns the unit off. 6 RReeaarr PPaanneell 27 26 Sticker area Keep out Serial REMOTE SWITCH 120V 60 Hz 300 WATTS GND. 0 WARNING: CAUTION RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.AVIS: TO RAIN OR MOISTURE. ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO REDUCE THE RISK OF FIRE OR TRANSTUBE 100 EFX HD EFX LEVEL EFXEFXPRE AMP OUT PWR AMP SENDRETURN -10 dBV (.3V RMS) 0 dBV (1V RMS) LOOSE POWER DAMPING MEDIUM TIGHT 100W 50W 25W SPEAKER OUTPUTS 100 WATTS RMS/40V RMS, 4 OHMS MIN. SPEAKER JACKS PARALLELED IMPEDANCE SELECTOR 416 8 R 1616 23 25 20 19 17 22 21 1824 ( ((1 116 66) ))R RRE EEM MMO OOT TTE EE S SSW WWI IIT TTC CCH HH This eight-pin DIN connector is provided for connection of the PFC 3 footswitch (included). The footswitch cable should be connected before the amp is powered up. See the FOOTSWITCH section of this manual for explanation of footswitch operation. ( ((1 117 77) ))E EEF FFF FFE EEC CCT TTS SS L LLE EEV VVE EEL LL S SSW WWI IIT TTC CCH HH Selects the effects loop operating level: -10 dBV (0.3V RMS) when “out” and 0 dBV (1 V RMS) when “in”. ( ((1 118 88) ))E EEF FFF FFE EEC CCT TTS SS S SSE EEN NND DD Output for supplying signals to external low-level effects or signal processing equipment. ( ((1 119 99) ))E EEF FFF FFE EEC CCT TTS SS R RRE EET TTU UUR RRN NN Input for returning signals from external low-level effects or signal processing equipment. ( ((2 220 00) ))P PPR RRE EEA AAM MMP PP O OOU UUT TT The preamp out can be used to route the amplified signal from the preamp to a mixing console, tape recorder, etc. Connect the preamp output to line-level inputs of other equipment using high quality shielded cable. This patch does not affect operation of the amplifier. ( ((2 221 11) ))P PPO OOW WWE EER RR A AAM MMP PP I IIN NN Used to connect line-level signals to the power amplifier section. Connect the power amp input to line-level output of other equipment using high quality shielded cable. This patch disconnects the preamp section from the power amp section. ( ((2 222 22) ))D DDA AAM MMP PPI IIN NNG GG This three-position switch allows for adjustment of the damping factor of the power amplifier. Damping is the ability of an amplifier to control speaker cone motion after the signal disappears. A higher damping factor (TIGHT) reduces cone vibration more quickly than a lower damping factor (LOOSE). This switch works much like the Resonance and Presence controls found on other Peavey amps, if they were to be turned simultaneously. If the Damping switch is changed, the volume level of the amp will also change and may require re-adjustment of the volume. ( ((2 223 33) ))P PPO OOW WWE EER RR This three-position switch selects the power output level of the power amplifier. This switch works like the T. Dynamics® control found on other Peavey amplifiers which provides for a more pronounced tube power compression simulation at lower settings. 7 ( ((2 224 44) ))S SSP PPE EEA AAK KKE EER RR O OOU UUT TTP PPU UUT TTS SS These paralleled 1/4" mono (TS) jacks are provided for the connection of speaker enclos...
Эта инструкция также подходит к моделям:Музыкальные инструменты - TransTube 100 EFX (2.13 mb)