Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
(21) STANDBY SWITCH This two-way toggle switch allows the amp to be placed in the STANDBY mode. In the STANDBY position the tubes stay hot but the amplifier is not operational. Switching to the ON position places the amp in active mode. This switch should be turned on a few minutes after the power switch in order to warm up the tubes. (22) POWER SWITCH This two-way toggle switch applies mains power to the unit. The red power status lamp (20) will illuminate when this switch is in the ON position. This switch de-activates only one side of the mains‚ use caution when servicing. 6 7 (23) CHANNEL SELECT This switch selects the channel (Ultra or Rhythm). The active channel LED illuminates to indicate the active channel. (24) EFX ADJUST Pressing this control selects the effect. A yellow LED adjacent to the effect name will illuminate to indicate the selected effect. Rotating this control clockwise changes the parameter of the active effect according to the descriptions below. The surrounding LED ring indicates relative value of the parameter being adjusted. EFX ADJ PARAMETERS Tremolo: Rate increase Funk wah: Sensitivity increase Octaver: Wet/Dry mix Rotary Speaker: Rate increase Flanger: Rate increase Phaser: Rate increase Chorus: Rate increase/depth decrease EFX amps are built with factory settings loaded into the presets. To return to the factory settings, first turn the power to OFF. Then‚ press and hold both the EFX ADJUST (24) and DELAY (26) controls while turning the amp back on. (25) VOLUME BOOST This control adjusts the level of Volume Boost. The surrounding LED ring indicates level. (26) DELAY This control adjusts delay type, time, and volume. Three types of delay are available: SLAP (1 repeat), ECHO (3–4 repeats), or INFINITE (5–6 repeats). The LEDs in each section of the control indicate which type is active and level. Pressing the control twice sets the delay time to the interval between presses. Triple XXX® 40 EFX 23 24 25 26 8 REAR PANEL 28 34 29 30 31 32 33 Triple XXX® 40 EFX Triple XXX® 40 27 (27) Fuse A fuse is located within the cap of the fuse holder. This fuse must be replaced with one of the same type and value to avoid damaging the amplifier and voiding the warranty. If the amp repeatedly blows the fuse, it should be taken to a qualified service center for repair. Warning: The fuse should only be replaced after the power cord has been disconnected. (28) Ground Polarity Switch This three-position, rocker-type switch should normally be placed in the center (0) position. If hum or noise is noticed coming from the speaker enclosure(s), the switch may be placed in the “+” or “-” position to minimize hum/noise. If changing the polarity does not alleviate the problem, consult your authorized Peavey dealer, the Peavey factory or a qualified service technician. (29) Remote Switch (Triple XXX® 40 only) This 1/4" connector is provided for the connection of the remote footswitch. The footswitch cable should be connected before the amp is powered up. See the FOOTSWITCH section of this manual for explanation of switch operation. (30) Speaker Output This 1/4" mono (TS) jacks is provided for the connection of speaker enclosure(s). Minimum speaker impedance is 16 ohms. (31) Damping Switch This 3-position switch allows adjustment of the amplifier’s damping factor. Damping is the ability of an amplifier to control speaker cone motion after a signal disappears. A high damping factor (TIGHT) reduces cone vibration quicker than a low (LOOSE) factor. This switch works much like the resonance and presence controls on other Peavey amps, if those controls were turned simultaneously. If the DAMPING SWITCH is changed, the volume of the amp will also change and require re-adjustment. (32/33) Effects Send/Return These 1.4" mono (TS) jacks allow signal to be sent to‚ and returned from‚ external effects and/or signal processors. Using shielded cables with 1.4" mono (TS) phone plugs, patch from EFFECTS SEND to the input of the external device and from the output of the external device to EFFECTS RETURN. Only devices that do not increase signal gain should be used in this effects loop (chorus, delay, reverb, etc.). (34) Remote Switch (Triple XXX® 40 EFX only) This seven-pin DIN connector is provided for the connection of the remote footswitch. The footswitch cable should be connected before the amp is powered up. See the FOOTSWITCH section of this manual for explanation of switch operation. 9 FOOTSWITCH Triple XXX® 40 Triple XXX® 40 EFX CHANNEL BOOST 35 36 (35) Channel Select Button Depressing this button allows you to switch between the Ultra and Rhythm channels. The corresponding LED will illuminate to indicate which channel is active. (36) Volume Boost Button Depressing this switch allows you to toggle your volume boost on or off. Set your volume boost (17 or 25 depending on which version of the amp you own) and then kick this button everytime the drummer gets too loud! (37–44) Mode Select The PFC 3 footswitch operates in...
Эта инструкция также подходит к моделям:Музыкальные инструменты - Triple 40/EFX (3.09 mb)