Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
A microphone does not possess the ability to interpret the direction a sound is coming from in the same way that the human ear does. However, when the audio source is recorded, directional audio cues are still present in the recording. By breaking down the stereo signal into its various signal components, it is possible to isolate and restore these spatial cues and place them in the proper space relative to the direct sounds, such as a soloist or dialogue. These spatial cues are restored by the use of Head Related Transfer Functions (HRTFs), which process ambient sounds via patented frequency response correction curves. 15. WIDTH CONTROL -This knob is used to control the amount of SRS® 3D process that is applied to the output source signal. 16. TRUE BASS LEVEL -This knob is used to control the amount of "TRU BASS" process that is applied to the output source signal. ©American Audio® --Q-D6 SRS™ Instruction Manual Page 9 17. MICROPHONE SECTION - These controls are used to adjust the microphone volume level, treble level, and bass levels. MICROPHONE VOLUME - This knob is used to regulate the microphone output volume. Turn- ing the knob in a clockwise direction will increase the volume level. MICROPHONE TREBLE CONTROL -This knob is used to adjust the treble levels of the Microphone with a maximum signal gain of 10dB or maximum signal decrease of -10dB. Turning the knob in a counter-clockwise direction will decrease the amount of treble applied to the microphone signal, turning the knob in a clockwise direction will increase the amount of treble applied to microphone signal. MICROPHONE BASS CONTROL -This knob is used to adjust the low frequency levels of the microphone with a maximum signal gain of 10dB or maximum signal decrease of -10dB. Turning the knob in a counter-clockwise direction will decrease the amount of bass applied to the microphone signal, turning the knob in a clockwise direction will increase the amount of bass applied to microphone signal. 18. TALKOVER CONTROL -This function decreases all signal output except for the microphone signal. 19. MASTER VOLUME LEVEL INDICATORS - The dual MASTER LEVEL LED indicators are used to detail the master output level. The meters will detail the output level of both the left and right channels. ©American Audio® --Q-D6 SRS™ Instruction Manual Page 10 Rear Panel 20 2122 32 31 30 2928 2726 252423 20. PLAYER CONTROL - These jacks are used to control the “Q-Start” function between the mixer and a compatible American Audio CD Player. Input mini plugs from CD player controller into these jacks, input CD 1 into jack A and CD 2 into jack B. 21. GND (GROUND TERMINAL) -Connect each of your turntables ground leads to either of the two ground terminal. This will reduce the humming and popping noises associated with magnetic phono cartridges. 22. MICROPHONE 2 CONNECTOR - This jack is used to a connect a microphone to the mixer. Connect you microphone via 1/4 inch (6.3mm) jack. The signal volume will be controlled by the MIC LEVEL (17). The bass and treble levels can also be adjusted by the built-in MICROPHONE EQ (17). 23. CHANNEL 1: PHONO 1 INPUT JACKS - Connect turntables equipped with MM pickup cartridge to PHONO inputs (All DJ turntable use MM pick-up cartridges). The red colored RCA jack represents the right channel input and the white represents the left channel input. 24. CHANNEL 1: LINE 1 RCA INPUT JACKS - DO NOT CONNECT TURNTABLES TO THESE JACKS! These Jacks are used for line level inputs. Connect CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables should only be connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the white represents the left channel input. 25. CHANNEL 2: PHONO 2 INPUT JACKS - Connect turntables equipped with MM pickup cartridge to PHONO inputs (All DJ turntable use MM pick-up cartridges). The red colored RCA jack represents the right channel input and the white represents the left channel input. 26. CHANNEL 2: LINE 2 RCA INPUT JACKS -DO NOT CONNECT TURNTABLES TO THESE JACKS! These Jacks are used for line level inputs. Connect CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables should only be connected to “Phono” inputs. The red colored RCA ©American Audio® --Q-D6 SRS™ Instruction Manual Page 11 jack represents the right channel input and the white represents the left channel input. 27. CHANNEL 3: LINE 3 AUX INPUT JACKS - DO NOT CONNECT TURNTABLES TO THESE JACKS! These Jacks are used for line level inputs. Connect CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables shoul...