Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
Do not permit operation by persons not qualified for operating the unit. Most damages are the result of unprofessional operation! • Do not attempt to operate this unit if the power cord has been frayed or damaged. • Disconnect from main power before making any type of connection. • Do not attempt to operate this unit, if it becomes damaged in any way. • Never operate this unit when it’s covers are removed. • To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture. • This unit is intended for indoor use only, use of this product outdoors voids all warranties. • During long periods of non-use, disconnect the unit’s main power. ©American Audio® - - WM-700™ Instruction Manual Page 4 WM-700™ Receiver CONTROLS AND FUNCTIONS BALANCEDPOWERUNBALANCEDAUDIOOUTPUTLINEMICSQUELCHDC ONLY12V 500mAFREQCHP4P3CHGPP1P2SCANMANUALC7C8RFMHzC5C4C1C2C3PRESETC6SETAFVOLUMEDCOUT 1 2 5 3 4 6 9 11 6 7 8 10 1. Power Button - Press this button for 4 seconds to turns On the receiver. 2. LCD Screen - The LCD screen will show the channel number, AF & RF signal strength, Frequen- cy level, and setup mode. 3. UP Button/Set Button/DOWN Button - UP & DOWN Buttons: These buttons are used to select your desired mode, and search for your desired channel. Mode Selection: Press and hold to select “MANUAL” or “SCAN” or “PRESET”. Every 2 seconds it will switch to the next mode, release the button when your desired mode is highlighted. “MANUAL” mode: When the LCD display starts flashing, please press this button to move the number forward. “SCAN” mode: When the LCD display starts flashing, please press this button to scan in forward direction. “PRESET” mode: Press this button to change the preset group. Set Button: Use the Set button to search for your desired channel after you have selected your desired mode. Press for 2 seconds, until “MUTE” is displayed and the LCD display is flashing. Then press either the UP or DOWN buttons to change the channel. Stop pressing the button and the LCD display will flash five times and then lock the setting. 4. Volume Knob - Controls the volume of the receiver output. 5. DC Out - Use this supplied cable to connect the receiver and the microphone. It takes around 10 hours to charge. ©American Audio® - - WM-700™ Instruction Manual Page 5 6. Antennas - Receives RF signals from the transmitter. 7. 12v DC Input - Connect the included power supply to this input, or any other 12v power adapter. 8. Squelch Adjustment - The squelch adjusts the output level to prevent external noise. If you set the squelch to high you will reduce the range of the system. Set the squelch to a minimum before turning the receiver on. 9. Mic/Line Switch - This switch lets you select your output source. If your connected to the line input on a mixer or amplifier set the switch to “Line”. If your connected to a Mic input on a mixer or amplifier set the switch to “Mic”. 10. Unbalanced 1/4” Output - This unbalanced output can be used to connect the receiver to the line-level input of a mixer or amplifier. 11. Balanced XLR Output - This balanced XLR output can be used to connect the receiver to balanced input of mixer or amplifier. WM-700™ Receiver CONTROLS AND FUNCTIONS Cont. WM-700™ Receiver Modes Manual Mode: In manual mode you can set your desired channel manually. 1. Select manual mode by pressing and holding either the UP or DOWN buttons until MANUAL is highlighted in the LCD. 2. Press the SET button for 2 seconds. The LCD will start to flash and “MUTE” will appear in the LCD. 3. Press the UP and DOWN buttons to find your desired channel or an interference free channel. After you have found your channel release the button and let the LCD flash 5 times and you selec- tion will be locked into the channel setting. Auto-Scan (Scan) Mode: In Scan mode you can let the receiver scan to for a clear channel. 1. Select auto-scan mode by pressing and holding either the UP or DOWN buttons until Scan is highlighted in the LCD. 2. Press the SET button for 2 seconds. The LCD will start to flash and “MUTE” will appear in the LCD. 3. Press the UP and DOWN buttons to find your desired channel or an interference free channel. After you have found your channel release the button and let the LCD flash 5 times and your se- lection will be locked into the channel setting. Preset Mode: In Preset mode you can select a Preset channel that is pre-programmed into the receiver. There are 4 Preset groups with 8 default channels in each group. Each of the 8 default channels are different in each of the 4 Preset groups. 1. Select Preset mode by pressing and holding either the UP or DOWN buttons until Preset is high- lighted in the LCD. 2. Press the SET button for 2 seconds. The LCD will start to flash and “MUTE” will appear in the LCD. 3. Use the UP button to scroll through the 4 Preset groups, and use the DOWN button to scroll through the 8 default channels in each Preset group. After you have found...
Эта инструкция также подходит к моделям:Музыкальные инструменты - WM-700LAV (1.02 mb)