Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
55ASSIGNCH .............. ASSIGNCH ...................................... RIGHT-15-10-50+5 .................................................... American Audio would like to thank for your purchase of this great product. For those of you that are to impatient to read the entire user manual we have compiled these quick start instructions. We hope that you will at least read through these instructions to familiarize yourself with the basic understanding of the unit. The DX4™ is part of American Audio’s continuing evolution in audio technology. This unit has been built and designed with the typical DJ in mind, by DJ’s. We have attempted to provide you with the most reliable product on the market by using only components made from quality products. MASTER LEVEL (5) - Use this level control to set your volume output. Try never to send an output of more than +4dB to your system. Signal at levels higher than this will start to distort and may cause damage to your system and speakers. Remember that a distorted signal from you mixer will only be multiplied throughout your system. HEADPHONES (16) -To avoid sever hearing damage, always be sure the headphone level is set to minimum before plugging them in. Never put the headphone on without making sure the headphone level is turned down. MICROPHONE 1 (1) - The main mic connector uses a 1/4” jack unbalanced connector on the rear of the unit or XLR balanced connection on the face of the unit. Both microphone connection marks as MIC 1 are controlled by the MIC 1 VOLUME knob. Always leave the mic level to it’s minimum level when not in use. BALANCED XLR OUTPUTS (18) -The Master Output includes a pair XLR Balanced JACKS as well as a pair RCA UNBALANCED JACKS (19). The 3-pin XLR jacks send a high current balanced output signal. These jacks should be used when you will be driving an amp or other audio equipment with a balanced input, or whenever you will be running a signal line greater than 15 feet. Always, use these jacks whenever possible. FADER ASSIGN SWITCH (11) -This is a five position switch that assigns a channel to the CROSSFADER (12). When a channel is assigned to the left side of the CROSSFADER (12) that channels output level is routed to and controlled by the CROSSFADER (12). Sliding the CROSSFADER (12) to left position will send the volume output of the assigned channel to the MASTER VOLUME LEVEL (5), siding the CROSSFADER (12) to right position will cut that channels volume to MASTER VOLUME LEVEL (5). The reverse is true for the right channel fader assign switch. When the assign switch is set to the "OFF" position the crossfader will have no function. BOOTH LEVEL (BOOTH LEVEL VOLUME CONTROL) (13) -This rotary knob is used to control the output volume to any source connect to the BOOTH OUTPUT JACKS (25) on the rear of the unit. Be sure this volume control is always set to zero before turning the unit on and off. ©American Audio® --DX4™ Instruction Manual Page 4 DX4™ Controls and Features Top Panel 123 4 567 8 MIC1LINE1PHONO1LINE2PHONO2LINE4LINE3LINE6LINE5CUECUECUECUEMIC1VOLUME100BASS100MIDLOW100MIDHIGH100TREBLE100LEFT+50-5-10-15MASTERLEVELMASTERLEVEL100BOOTHLEEL100CUEMIXINGPGMCUECUELEVEL100PHONESPOWERMIC2VOLUME100 ........................ 55555555ASSIGNCH .............. ASSIGNCH ...................................... RIGHT-15-10-50+5 .................................................... 9 1011 12 13 14 15 16 1. MIC 1 VOLUME (MICROPHONE 1 VOLUME LEVEL) -This rotary knob is used to control the volume output level for any microphone connected to the MIC 1 INPUT JACKS (2 or 31) . Turning the knob in a clockwise direction will increase volume output. 2. MIC 1 (MICROPHONE 1 INPUT) -This jack accepts a standard XLR 3-pin balanced male plug. The volume output level for this microphone is controlled by the MIC 1 VOLUME KNOB (1). 3. CHANNEL SOURCE SELECTOR SWITCH (TRANSFORMER SWITCH) - These switches are used to select the input source assigned to each channel. Each channel may only be assigned one input source at a time. This switch must be in the “phono” position for turntable operation. For all other input devices such as CD players and tape decks this switch must be in the “line” position. 4. CHANNEL FADER -The channel faders are used to control the output signal of any source assigned to its particular channel. However, the master volume for all channels is controlled by the MASTER VOLUME CONTROL (5). 5. MASTER VOLUME CONTROL -This rotary knob is used to control the master output level (volume). To avoid distorted output maintain an average output signal level of +4 dB. Be sure this volume control is always set to zero before turning the unit on. 6. MASTER OUTPUT 4-BAND EQ - The DX4 includes a 4-band master output EQ. The adjustable EQ bands are bass, mid low, mid high, treble. These knobs are used to increase (+20dB) or decrease (-30dB) the band width of each frequency applied to the output source signal. Turning the knobs in a counter-clockwise dire...