Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
• MMT Technology with 16 different types of synthesis for totally new and dynamic sounds. • Performance Arpeggiator with Ribbon and Slider and 32 selectable scale types for instant fun and inspiration. • Modulation with 5 MIDI syncable LFO shapes to create more complex and expressive sounds. • New Multi-Mode Resonant Filter with four types: Low Pass, High Pass, Band Pass and Band Pass, + and Drive parameter. • Three Stereo Effects processors with 16 different effects to select from and selectable effects routings. Text Box: • Expanded Motion Sequence function with up to 24 parts of Motion Sequence per pattern. • Up to 8 bars per pattern allow for a more complete sounding pattern and up to 64 songs, 4 outputs, a large easy to read LCD screen and much more. Getting Started – Basic Overview of Knobs, Switches and Panel Layout / Preload The EMX-1 is very simple to use, once you understand the basic layout. To access the different modes of the EMX-1 (PATTERN, SONG, GLOBAL, etc.) you press any of the mode keys right above the transport section (....../..). To access any pages within that mode, use the ....(up/down) keys to the left of the mode keys, and then use the VALUE dial to change values in the LCD screen. To play or hear a part, press the corresponding part key (i.e. DRUM PART, SYNTH PART). DRUM parts will play once you press the key, SYNTH parts will only play by pressing any of the 16 step keys which also double as keys on a keyboard. To change the octave range of the step keys/keyboard, press the .... keys just above the step keys. Once a part is selected (key is lit), you can adjust the settings in the PART COMMON, MODULATION, and/or SYNTH OSCILLATOR and SYNTH FILTER sections, by turning any knobs in that section. Some keys in each section work in a cyclical nature; others work in a simple toggle on/off mode. Additional pages and functions in each mode are available by pressing and holding the SHIFT key, and then pressing one of the desired 16 STEP keys to access the function (i.e. CLEAR PATTERN, SHIFT NOTE). Reloading the Factory Data - Preload 1. To reload the factory data, first make sure that any custom data is saved to SmartMedia (see page 5), and then power – off the EMX-1, hold down the WRITE and SOLO keys, and power-up. When the display prompts “Preload Sure?”, press the flashing PLAY/PAUSE (../..) key. Selecting and Playing Demo Songs 2. Connect the AC power supply to the EMX-1 and connect the L/MONO and R outputs to a powered monitor system or connect headphones to the Headphones jack of the EMX-1. Make sure that the MASTER VOLUME and TUBE GAIN knobs are turned all the way to the left. 3. Press the SONG key and then press the PLAY/PAUSE (../..) key to begin playback and adjust the level of the MASTER VOLUME knob so that it is at a comfortable volume. To stop playback, press the STOP (..) key. 4. To select a different song, turn the VALUE dial to the right of the screen. Selecting and Playing Patterns 1. Press the PATTERN key and then press the PLAY/PAUSE (../..) key to begin playback. 2. Use the Value dial to select different patterns. To stop playback, press the STOP (..) key. Pattern Mode - Muting and Soloing Parts 1. To mute a part, press and hold the PART MUTE key and then press the part key that you would like to mute. 2. To solo a part, press and hold the SOLO key and then press the part key that you would like to solo. To undo a soloed or muted part key, either repeat the same process or just tap the SOLO key. 3. You can also quickly mute all parts or solo all parts of a specific type (i.e. all DRUM PARTs) by pressing and holding the SHIFT key (just above the 16 step keys) and then repeating step 1 or 2. Changing Tempo 1. To change the tempo of a pattern, press the .. key once so that the LCD screen shows Tempo and its value, and then use the Value Dial to change the tempo value. Selecting a Wave on a Drum Part 1. Press the PART EDIT key to enter the PART EDIT mode. 2. Press the PART key that you would like to select a wave on. 3. Use the Value dial to change the number of the sample wave or the waveform type that is displayed in the LCD screen. Selecting a SYNTH OSCILLATOR and editing a SYNTH PART 1. Press any SYNTH PART key and then press the PART EDIT key to enter the PART EDIT mode. 2. Turn the SYNTH OSCILLATOR knob to select the desired SYNTH OSCILLATOR type. 3. Use the VALUE dial to change the SYNTH PART waveform and then use the OSC EDIT 1 and OSC EDIT 2 knobs to adjust the parameters of the selected SYNTH OSCILLATOR. The LCD screen will indicate the parameter that is assigned to OSC EDIT 1 and OSC EDIT 2 and its value. Working with the PART COMMON, MODULATION and FILTER sections 1. Press the PART key that you would like to adjust settings in any of these sections. 2. Turn any knob in those sections to adjust parameters, the LED screen will indicate which parameter you are adjusting and its value. 3. To select any parameters that are assigned to keys, press the corresponding key...