Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
If a mixer is placed between two turntables make sure that there is at least ." (7mm) between the mixer and the turntables to prevent damage to the turntables and to reduce unwanted system noise. Mixer Mixer 85 mm ." ." Mixer ." ." Setup Style 1 (traditional) Best For: Long mixes and blending techniques Setup Style 2 (battle style, scratching) Mixer Best For: Scratching, cutting, and aggressive mixing techniques There are many variations of these setups. Find the best setup that works for your mixing style by experimenting with different turntable and mixer placements. It is strongly recommended that the top mixer surface and the top flat surface of the turntable be at the same level. SETUP & INSTALLATION PAGE 2 PLATTER SETUP WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instability, or permanent motor damage. 1. Start by inspecting the bottom of the aluminum platter to check that both locking pins have rubber fittings on them. 2. Next, rotate the top of the motor assembly (brass in color) so that two holes are aligned parallel with the front of the turntable. 3. Install the platter onto the center spindle and motor assembly making sure that the Numark logo and the two holes are aligned parallel with the front of the turntable. 4. The two locking pins should drop into the top of the motor assembly for a stable and secure fit. If they do not, grasp the center spindle with one hand while rotating the platter with the other until the locking pins drop into place. If the platter is properly installed, it should not wobble and should rotate smoothly without any noise. 1. 2. Locking Pins ALIGNED 3. 4. PAGE 3 PLATTER SETUP CARTRIDGE SETUP For Head Shell Mounted Cartridges: The cartridge that comes with this turntable should be preinstalled on the head shell. If it isn't, please follow the below instructions for installing a cartridge onto the head shell. 1. Position the head shell and the cartridge so that the four connector pins are visible. Make sure that the stylus cover is installed to prevent damage to the stylus during installation. 2. Prepare to connect the cartridge to the head shell using the green, red, blue and white connector wires. 3. Starting with the upper left pin and going clockwise install the white, the red, the green and finally the blue wires to the connector pins. Be careful not to bend the metal clips on the end of the wires. These metal connectors should never make contact with one another. 4. Using the screws and bolts that are included with the cartridge, loosely fasten the cartridge to the head shell body. 5. Once temporarily fastened, position the cartridge so that both screws are aligned with the optimum position mark on the Head shell (Numark HS 1 Head shell and Numark Cartridges only.) Moving the both screws to a mark away from the optimum position indicated on the head shell may increase or decrease performance depending on the cartridge used. For safe vinyl record treatment, the screws should always be aligned perpendicular to the head shell (any angle may increase "record burn.") 6. Once the cartridge is positioned correctly, secure the cartridge to the head shell by tightening the mounting screws. For Integrated Head Shell Cartridges (Numark CS-1, CC-1, CX-1, etc.) 7. Align the pin on the rear of the Cartridge Assembly so that it is in a vertical position and insert it into the tone arm lock nut. 8. Secure the cartridge to the tone arm by turning the tone arm lock nut clockwise until the head shell feels secure and does not wobble to the left or right. WARNING: Over tightening the tone arm lock nut may result in permanent damage to the tone arm or the cartridge. 9. Remove the stylus protector before playback. 1. 2. 3. 4. Cartridge Headshell Connector Pins Cartridge Headshell W R G B White Blue Red Green DO NOT TIGHTEN! 5. 6. 7. 8. INTERCHANGING TONEARM TUBES (sold seperately) WARNING: An incomplete understanding of this procedure could lead to permanent damage to the headshell, your records, or the tonearm assembly. NOTICE: Interchanging tonearm tubes unnecessarily may shorten the life of the tonearm tubes and/or tonearm components. This turntable features the world's only tonearm assembly capable of accommodating two different tonearm tube styles: S-Shaped and Straight. The S-Shaped tube produces a higher signal to noise ratio with most cartridge assemblies. The Straight tube is ideal for heavy back-cueing or scratching. Decide which tube to use based on your mixing style. 1. Power off the turntable and any connected mixers, amplifiers or monitoring devices. 2. Remove the Cartridge from the tonearm tube that is currently installed on the tonearm tube by rotating the locking collar counter clockwise. 3. Unclip the tonearm tube from the armrest. 4. Remove the tonearm tube by rotating the locking collar counter clockwise. 5. Insert the desired tonearm into the tonearm assembly with the screws FACING TOWARDS THE TURNTABLE BODY. 6. Tighten the tonea...