Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Make sure all items listed on the front of this guide are included in the box. 2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT. 3. Study this setup diagram. Note: This turntable can be used as a standalone unit, as well as with the items listed in the quick setup diagram. 4. Make sure all devices are turned off and all faders and gain knobs are set to “zero” 5. Connect all stereo input sources as indicated in the diagram. 6. Connect the stereo output devices to power amplifier(s), tape decks, and/or other audio sources. 7. Plug all devices into power. 8. Switch everything on in the following order. • Turntable • Mixer (not included) • last, any amplifiers or output devices (not included) 9. When turning off, always reverse this operation by, • turning off amplifiers (not included) • mixer (not included) • Turntable 10. Go to for product registration. More information about this product may be found at BATTERY INSTALLATION This product can be powered by 6 “D” Cell batteries. They should be loaded as show above, with the positive end toward the handle. PRODUCT FEATURES 1. Platter: Place your record on the platter. 7. Dust Cover: This cover protects the turntable from dust 2. Control Panel: Please see the alternate detailed and abuse while not in use or while in transport. section on the control panel features. 8. Dust Cover Latch: This latch holds the dustcover 3. On Board Speaker: Use this speaker to listen to the securely in place, and can easily be opened by sliding it to audio. the left. 4. Tone Arm Clip: Use this clip to secure your 9. Carry Handle: Use this handle easily remove the unit tonearm when storing and transporting the unit. from record crates and bags, as well as carrying it in 5. Tonearm: This unit comes with a ready to use pre- transport. balanced tonearm and cartridge. The cartridge is 10. Battery Cover: This holds the batteries securely in place user replaceable with parts from your distributor during use and transport. It easily slides open and closed located in the warranty guide. The platter starts as indicated on the cover itself. NOTE: This unit uses 6 spinning once the tonearm is lifted over the “D” cell batteries (not included). They should be installed record. in the proper direction indicated 6. 45 Adapter: Use this adapter with 45 rpm records. Output Panel Features 1. Power Switch: Use this switch to turn the power on and to the OFF position before plugging in any headphones to off. avoid permanent hearing damage. 2. AC In: This turntable is designed to work with either 6. USB Audio Output: Use the included USB Cable to batteries or the power supply cord that comes with it. connect your turntable to your computer. Refer to the While the power is switched off, plug the power supply into software instruction guide before plugging in your the turntable first, then plug it into the wall power outlet, turntable. then switch on. NOTE: This unit can also be powered by 6 7. Gain: This knob can be used to adjust the gain level of the “D” Cell batteries ( Not Included). audio signal from the turntable. If the audio from the 3. Master Output ( RCA) : This “ line level” output is for turntable is too quiet or too loud, use this knob to adjust connecting to the input of an external audio device such as the volume setting. a DJ mixer, tape recorder, CD Burner, PA system, powered 8. 1/8” Stereo Line Input: Connect Tape Players, Reel to speaker, or a home stereo. The level of the master stereo Reel, or any other audio source here. This signal is sent to output signal is controlled by the audio level control. the computer through the USB connection. Make sure 4. 1/8” Headphone Jack: Use this jack with the 1/ 8” mini that your phono cartridge is installed while using this headphone plug. NOTE: Be sure the volume control is set input for maximum sound quality. Also make sure that to the OFF position before plugging in any headphones to your RCA jacks are either plugged into an input device or avoid permanent hearing damage. not in contact with metal. 5. 1/4” Headphone Jack: Use this jack with the 1/ 4” Note: The 1/8" audio input is not routed to the turntable's headphone plug. NOTE: Be sure the volume control is set RCA output jacks, only to your computer via USB. POWER PITCH 33 RPM 7845 +10% -10% TONE LOW HIGH AUDIO OFF CONTROL PANEL FEATURES 1. Audio Level Control: This rotary control adjusts NOTE: In order for the pitch to be adjusted, the the volume level of the onboard speaker, tempo also changes according to what the pitch headphone and line out outputs. NOTE: Make sure setting. the Audio Level Control is set to OFF when 4. RPM Selection Switch: This switch selects the connecting any alternate audio output devices. RPM of the turntable platter -- 33, 45, and 78 RPM. 2. Tone Control: This feature allows you to adjust 5. Power LED: This LED indicates that the power the low and high frequency audio levels. switch on. Make sure the pow...