Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
1 DAS-AMFM Satellite Radio Tuner Module • The DAS-AMFM Tuner Module can be used with both Mi-Series and Tango Audio Controllers. • All Mi-Series and Tango Audio Controllers come equipped with a DAS-AMFM Tuner Module. The Mi-Series and Tango Audio Controllers support two Tuner Modules (DAS-AMFM and/or DAS-SIRIUS) in any combination (one of each, or two of either module). Refer to the DAS-SIRIUS Installation Guide for details on installing the DAS-SIRIUS Tuner Module. • Each Tuner Module uses 1 source input on the Audio Controller. Installing/removing Tuner Modules requires removing the cover from the Audio Controller, removing the Tuner Option cover plate from the rear panel of the Controller, installing the Tuner Module, and setting Jumpers on both the Tuner Module to specify each Tuner as either TUNER 1 or TUNER 2, and on the Interface Board pin-bus of the Audio Controller to enable/ disable Tuner 1 and 2. WARNING: Disconnect all power sources before opening the chassis. Failure to disconnect power before performing this installation may cause injury or death. FIG. 2 provides orientation for the various internal components that must be accessed to install the Tuner and set the Jumpers. FIG. 2 Audio Controller - Internal view front Interface Board Pin Bus (Controller Jumpers) rear AMFM Tuner Module Tuner Ribbon Cable (20-pin) Slot 1 (with faceplate) installed in Slot 2 Tuner slots: Top = Slot 1 Bottom = Slot 2 Interface Board CAUTION: Make sure to discharge all static electricity from your body before touching any components of the tuner modules or the audio controller. Failure to do so may lead to permanent damage to the tuner or controller. Setting the Jumpers Mi-Series and Tango Audio Controllers come equipped with one DAS-AMFM Tuner Module, installed into Slot 2 (see FIG. 2). Mi-Series and Tango Audio Controllers support 2 Tuner Modules in any combination, this document describes installing the DAS-AMFM Tuner Module into Slot 1, leaving the factory-installed DAS-AMFM Tuner Module in Slot 2. Note: Because of the location of the Jumpers in the Controller and on the Tuner Module, it may be easier to make all jumper settings before installing the Tuner Module in the Controller. Audio Controller Jumpers - Location Examine the configuration of the jumpers on the left-side Interface Board Pin Bus, as seen when viewing the Interface Board from the front of the Controller (FIG. 3). FIG. 3 Audio Controller - Interface Board Pin Bus / Jumpers Audio Controller Jumpers rear panel Interface Board Pin Bus - Slot 1 (with faceplate installed) Slot 2 (with AM/FM Tuner module installed) (see Fig 4 & 5) Audio Controller Jumpers - ON/OFF Settings • ON position = pins 3 and 2 jumpered (with pin 1 exposed). • OFF position = pins 2 and 1 jumpered (with pin 3 exposed). ON position (Jumper pin 1 & 2) OFF position (Jumper pins 2 & 1) 3 1 3 1 Jumper (pins 3-2) exposed pin (1) Jumper (pins 3-2) Jumper (pins 2-1) exposed pin (3) Jumper (pins 2-1) exposed pin (1) exposed pin (3) FIG. 4 Controller Jumper Settings Audio Controller Jumpers - Dual Tuner Setting If two tuner modules are to be used, the Audio Controller jumpers should all be set to ON, as shown in FIG. 5: 3 1 3 1 Top Left of Interface Board Pin Bus 3 TUNER 1 Jumpers Tuner 1 jumpers (in ON position) 1 3 TUNER 2 1Jumpers Tuner 2 jumpers (in ON position) FIG. 5 Audio Controller Jumper Configuration (Dual Tuners) Move the TUNER 2 jumpers to the ON position by connecting the top 2 sets of pins (pins 3-2) and leaving the bottom pins (pin 1) exposed. DAS-AMFM Tuner Module Jumpers There are jumpers on the DAS-AMFM Tuner Module that must be set to differentiate Tuner 1 from Tuner 2 in the Controller. Note: All DAS-AMFM AM/FM Tuner Modules are shipped in the Dual Tuners Tuner 1 configuration. The instructions for setting these jumpers differ based on the color of the “Interface Board” (red or green), as described below: Red Interface Boards Examine the configuration of the jumpers located on the Tuner Modules, to the right of the 20-pin ribbon cable connector (as seen when viewing the installed modules from the front of the controller). • Note that there are two rows of 5 pins as shown in FIG. 6. • With only a single tuner, all pins are jumpered. (no jumpers) Dual Tuners: TUNER 1 Dual Tuners: TUNER 2 FIG. 6 Tuner Module Jumper Configuration (Red Interface Boards) Green Interface Boards Examine the configuration of the jumpers located on the Tuner Modules, to the right of the 20-pin ribbon cable connector (as seen when viewing the installed modules from the front of the controller). Note that there are two rows of 5 pins (FIG. 7). Cable Cable Tuner 1 Tuner 2 Configuration Configuration Jumper No Jumper FIG. 7 Tuner Module Jumper Configuration (Green Interface Boards) Remove all jumpers from the new tuner, and attach the 2-wire (red and white) end of the cable included with your kit to the pins (FIG. 8): Note the position of the Red and White wires relative to the connector FIG. 8 Aud...