Оценок - 1, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Step 2: Setting up the speakers By connecting the supplied speakers, you can enjoy Dolby Pro Logic Surround sound. Dolby Pro Logic Surround is a decoding system standardized in TV programs and movies. Dolby Pro Logic Surround improves the sound image by using four separate channels. These channels manipulate the sound to enhance the action as it happens on the screen. Since the center speaker cannot produce enough bass, the bass sound of the center channel is output from the front speakers. Center speaker Front Front speaker (L) speaker (R) Rear Rear speaker speaker (L) (R) Positioning the center and rear speakers Before you connect them, determine the best location for your speakers. 1 Place the front speakers at an angle of 45 degrees from your listening position. Center speaker Front Front speaker speaker (L) (R) 2 Place the center speaker so it is placed at about the same height as the front speakers (A). Align the center speaker with the front speakers or place it a little behind the front speakers’ position (B). A B 3 Place the rear speakers facing each other at about 60 to 90 cm above your listening position. Rear speaker 60 to 90 cm Rear speaker Rear speaker 45 (L) (R) continued Step 2: Setting up the speakers (continued) Adjusting the speaker volume To enjoy Dolby Pro Logic Surround sound, adjust the volume of each speaker using the test tone that the system provides. 1/u 1 (Power) VOLUME 1 3 VOLUME +/– 2,4 1 Press PRO LOGIC (or PRO LOGIC ON/OFF on the remote). The indicator on this button lights up. 2 Press T. TONE ON/OFF on the remote. The test tone is heard from the speakers in the following order. Adjust the volume of the test tone. nFront (left) nCenter Rear NFront (right) N 3 From your listening position, press CENTER LEVEL +/– and REAR LEVEL +/– on the remote to adjust the volume levels. The volume levels from each speaker should be the same. 4 Press T. TONE ON/OFF when you are done adjusting. The test tone is turned off. Note The test tone feature works only for Dolby Pro Logic Surround sound. Tip If you turn VOLUME (or press VOLUME +/– on the remote), all the speaker volumes change. Step 3: Setting the time You must set the time before using the timer functions. The clock is on a 24- hour system for the European model, and a 12-hour system for other models. The 24-hour system model is used for illustration purpose. 1 3,52,4 1 Press t/CLOCK SET. The hour indication flashes. 2 Press TUNING +/– to set the hour. 3 Press ENTER/NEXT. The minutes indication flashes. 4 Press TUNING +/– to set the minutes. 5 Press ENTER/NEXT. The clock starts. Tip If you make a mistake, start over from step 1. Step 4: Presetting radio stations You can preset the following number of stations: — 2 band model: 20 for FM and 10 for AM — 3 band model: 20 for FM, 10 for MW, and 10 for LW 2 Press TUNING MODE repeatedly until “AUTO” appears in the display. 3 Press TUNING +/–. The frequency indication changes and scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for a stereo program) appear. — 4 band model: 20 for FM, 10 for MW, 10 for LW, and 5 for UKV The bands you can select depend on the kind DISCALL DOLBY NR OFF AUTO TUNED STEREO MHzS of tuner built into your system. Confirm the bands by pressing TUNER/BAND 4 Press TUNER MEMORY. repeatedly. A preset number flashes in the display. 1/u 6 4 23,51 (Power) DISCALL DOLBY NR OFF AUTO TUNED STEREO S 5 Press TUNING +/– to select the preset number you want. DISCALL DOLBY NR OFF AUTO TUNED STEREO S 6 Press ENTER/NEXT. The station is stored. 7 Repeat steps 1 through 6 to store other stations. 1 Press TUNER/BAND repeatedly until the band you want appears in the display. Each time you press this button, the band changes as follows: 2 band model: FM .AM 3 band model: FM nMW nLW n 4 band model: FM nMW nLW nUKV* n * When you select this band, “STEREO Plus” appears in the display. To tune in a station with a weak signal Press TUNING MODE repeatedly until “MANUAL” appears in step 2, then press TUNING +/– to tune in the station. To change the preset number Start over from step 1. To change the AM tuning interval (Except for the European and the Middle Eastern models) The AM tuning interval is factory-preset to 9 kHz (10 kHz in some areas). To change the AM tuning interval to 10 kHz (or 9 kHz), press TUNER/BAND repeatedly until “AM” appears first, then turn off the system. While holding down ENTER/NEXT, turn the system back on. When you change the interval, the AM preset stations will be erased. To reset the interval, repeat the same procedure. Note The preset stations are canceled when you disconnect the power cord or if a power failure occurs for half a day. Connecting optional AV components To enhance your system, you can connect optional components. Refer to the instructions included with each component for details. Connecting a TV/VCR You can connect a TV and VCR to enjoy Dolby Pro Logic Surround encoded videos and TV programs. Be sure to match the color of the ...
Эта инструкция также подходит к моделям:Музыкальные центры - LBT-XB55AV (853.16 kb)
Музыкальные центры - LBT-XB80AV (853.16 kb)
Музыкальные центры - LBT-XB88AV (853.16 kb)
Музыкальные центры - LBT-XB88AVK (853.16 kb)