Оценок - 5, средний балл: 3.4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
AM loop aerial connection Connect the supplied loop aerial to the AM and the yterminals. To improve the FM reception STEP 1 Connect an outdoor FM aerial to the FM Connecting the Connecting the Stereo 75W terminal, using a 75-ohm coaxial cable Speakers and IEC standard socket connector. Installing the Speakers For speakers installation, see “Installing the Speakers”. Inserting the Batteries Right (R) and Left (L) satellite speakers Setting the Clock Connect the right speaker to the R connectors and the left speaker to the L connectors. Connect the grey cords with white stripes to Oand the solid grey cords to O. IEC standard socket connector (not supplied) AM FM 75W OOOOL R To improve the AM reception After you connect the AM aerial, connect a 6- to 15-meter (20- to 50- feet) insulated wire to the AM terminal. Connect the y terminal to earth. Important Superwoofer Ground the external aerial from yterminal Connect the superwoofer to the WOOFER against lightning. To prevent a gas connectors. Connect the grey cord with red explosion, do not connect the ground wire stripes to Oand the solid grey cord to O. to a gas pipe. OO STEP 2 Connecting the Insulated wires (not supplied) AM FM 75W Ground wire Aerials (not supplied) FM lead aerial (supplied)* AM loop aerial (supplied) FM 75W AM * Note: Extend horizontally Chapter 1: Setting up 4 Right satellite speaker to a wall outlet FM lead aerialSTEP 1 STEP 3 STEP 2 AM loop aerial Superwoofer Left satellite speaker Do this connection last! STEP 3 Connecting the Power Connect the mains lead to a wall outlet after you have made all the above connections. to a wall outlet Installing the Speakers Proper speaker positioning is essential in order to achieve directional effects and diffused ambiance. When you install the speakers, refer to the following instructions. Once you have determined the final placement, fasten the speakers to the speaker stands. Note Do not install the woofer close to the unit, and do not place the woofer above or below the unit. Otherwise, the vibration from the woofer may cause mechanical noise or “skipping”. When installing the speakers on either side of the main unit Place the woofer between the two satellite speakers. =+ When installing the satellite speakers away the woofer 1 Insert the supplied stand into the rear of the woofer. 2 Install the woofer between the satellite speakers with its front panel facing upward. When installing the satellite speakers away from each other Position the satellite speakers so they face toward your listening position. continue to next page O Chapter 1: Setting up O continued Fastening the speaker stands 1 Fasten the four screws loosely using the supplied wrench. Wrench Screw 2 Rotate the speaker to the desired position. You can also rotate the Sony logo. S 3 Tighten the screws. Note Tighten the screws securely to prevent mechanical noise. To attach the cord holder to the speaker stand Peel off the sheets covering the cord holders and attach the holders to the speaker stands. When attaching the speakers to the wall 1 Detach the caps and plates from the speaker stands. 2 Use a screw driver to attach the stands to the wall with four wood screws (not supplied). 3 Re-attach the caps and plates to the speaker stands. Note Before attaching the speakers, check the strength of the wall and the length of the wood screws to prevent the speakers from falling down. Inserting the Batteries Insert two R6 (size AA) batteries in the supplied remote for remote control. 1 Open the lid. 2 Insert two R6 (size AA) batteries. Match the + and – indications to the diagram in the battery compartment. 3 Close the lid. Battery life You can expect the remote to operate for about six months (using Sony SUM-3 (NS) batteries) before the batteries run down. When the batteries no longer operate the remote, replace both batteries with new ones. To avoid battery leakage If you are not going to use the remote for a long time, remove the batteries to avoid damage caused by corrosion from battery leakage. Setting the Clock The built-in clock shows the time in the display. You need to set the clock to utilise the timer-activated features of your stereo system. DISPLAY 3,5 1 2,4 1 Press CLOCK SET. The hour indication begins flashing. flashing 2 Set the current hour by turning the jog dial until the correct hour appears. flashing 3 Press ENTER/NEXT. The minutes indication begins flashing. flashing 4 Set the current minute by turning the jog dial until the correct minute appears. flashing 5 Press ENTER/NEXT. The clock starts running and the upper dot flashes. Use the time signal to set the clock accurately. The upper dot flashes for the first half of a minute (0 to 29 seconds), and the lower dot flashes for the last half of a minute (30 to 59 seconds). To check the time while power is on Press DISPLAY. The current time appears for a few seconds. To correct the clock setting Repeat steps 1 to 5. Chapter 1: Setting up For Your Information For Your Information...