Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
• Depending on the encoding/writing software, recording device, or the recording media used at the time an MP3 audio track is recorded, you may encounter such problems as disabled playback, sound interruptions, and noise. • When playing back an MP3 audio track, the playback elapsed time indication may differ from the actual time in the following cases. – When you play back a VBR (variable bit rate) MP3 audio track – When you perform Fast Forward or Rewind (Manual Search) Playing repeatedly — Repeat Play You can play all the tracks or a single track on a disc repeatedly. Press REPEAT repeatedly during playback until “REP” or “REP1” appears. REP: For all the tracks on a disc, or all the MP3 audio tracks in an album up to five times. REP1: For a single track only. To cancel Repeat Play Press REPEAT repeatedly until both “REP” and “REP1” disappear. Note When you select “REP1”, that track is repeated endlessly until “REP1” is canceled. CD/MP3 Play 11GB Creating your own program — Program Play You can make a program of up to 25 steps. You can synchro record the programed tracks onto a cassette tape (page 18). 1 Press CD (or FUNCTION repeatedly) to switch the function to CD. 2 Press PLAY MODE repeatedly in stop mode until “PGM” appears. 3 Press . or > repeatedly until the desired track number appears. When programing the MP3 audio tracks, press + or – to select album, then press . or > repeatedly until the desired track number appears. Selected track Total playing time number (including selected track) 4 Press ENTER. The track is programed. The program step number appears, followed by the last programed track number and the total playing time. 5 To program additional tracks, repeat steps 3 and 4. 6 Press N (or CD/NX on the unit). Program Play starts. Other operations To Do this Cancel Program Play Press PLAY MODE repeatedly in stop mode until “PGM” disappears. Erase the program Press CLEAR in stop mode. Each time you press the button, a track is cleared from the end of the program. Add a track to the end of Perform steps 3 and 4 in the program stop mode. Tips • The program you made remains after Program Play finishes. To play the same program again, press N (or CD/NX on the unit). However, the program is cleared when you open the CD compartment. • “– –.– –” appears when the total CD program time exceeds 100 minutes, or when you select a CD track whose number is 21 or over, or when you select an MP3 audio track. 12GB Tuner Scanning DAB stations Before you can receive DAB, you must register the contents of broadcasts (service components) so that they can be received by the DAB tuner using the DAB Automatic Scan procedure. DAB Automatic Scan DAB Automatic Scan starts automatically only when you turn on the system for the first time after you purchase the system. If you want to use the DAB Automatic Scan again, perform the procedure below. 1 Press DAB AUTO SCAN on the unit. “DAB Auto Scan? Push DAB” appears. 2 Press DAB on the unit. Scanning begins. “DAB Auto Scan” appears. Depending on the DAB services available in your area, scanning may take a few minutes. When scanning is complete, available service component list is created. Notes • If your country or region does not support DAB broadcast, “No Service” appears. • Do not press any button on the unit or supplied remote during DAB Automatic Scan. Scanning is interrupted and service component list may not be created properly. In this case, perform the DAB Automatic Scan again. • If you move to another area, repeat this procedure to store the stations for your new area. • This procedure clears all previously stored presets. • This procedure does not create any presets. To move system location When you wish to move the system to a new location, to preserve your own DAB settings, make sure the clock display* appears when the system is powered down, before unplugging the mains lead and DAB lead aerial. * In Power Saving Mode, make sure the clock display disappears. Tuner Presetting radio stations You can preset up to 20 DAB stations, 20 FM stations and 10 AM stations. You can then tune in any of those stations simply by selecting the corresponding preset number. Automatic tuning preset You can automatically tune in all of the service components or stations that can be received in your area and then store them. 1 Press TUNER/BAND (or FUNCTION repeatedly) to switch the function to TUNER. 2 Press TUNER/BAND repeatedly to select “DAB”, “FM” or “AM”. You can also use the DAB button to select DAB directly. 3 Press TUNING MODE repeatedly until “AUTO” appears in the display. 4 Press + or – (or TUNING + or – on the unit). Service component list is played downward (DAB) or the frequency changes as the system scans for a station (FM/AM). Scanning stops automatically when a station is tuned in. At that time, “TUNED” and “STEREO” (for stereo program only) appear. If “TUNED” does not appear and the scanning does not stop Set the frequency of the desired radio station as described in s...