Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Note: – After connecting all the speakers, do not forget to adjust the relative sound level between them. Front speakers and center speaker Connect the colored speaker wire to the coloured or + terminal, and the black wire to the black or - terminal of the appliance. 13 3139 116 18884 14 English 3139 116 18884 Surround speakers Connect the active speakers to the power source with the power cable provided. Switch on the active speaker with the POWER switch. Transmitter unit Connect the SURR terminal of the transmitter with the PRE OUT (SURROUND) terminal of the appliance using the supplied cinch cable. Connect the AC/DC adapter supplied to the 14 V socket of the transmitter. Then connect the AC/DC adapter to the power source. Note: – The SUB terminal of the transmitter is not used with this set. Positioning Position the unit in a way that you are able to ”see” the active surround speaker from the position of the unit. To avoid sound distortions caused by magnetic fields do not place the transmitter on your TV set. Positioning the speakers Important! To avoid overheating do not cover any vents and leave a minimum distance of 5 centimeters (2 inches) for ventilation. General hints for positioning Avoid positioning the speakers in a corner or on the floor, as this will boost the bass tones too much. Placing the speakers behind curtains, furniture etc. will reduce the treble response, thus reducing the stereo effect considerably. The listener should always be able to ”see” the speakers. Each room has different acoustic characteristics and the positioning possibilities are often limited. You can find the best position for your speakers by following the picture above. The speakers should always be arranged as symmetrically as possible in the room. Positioning the center speaker The center speaker should be placed in the center between both front speakers, e. g. underneath or on top of the TV. The best height for the center speaker is at the height of the listener’s ears (while seated). Positioning the surround speakers The surround speakers should face each other and be in line with, or at most 1.5m (4ft 6ins) behind the listener. Setup Adjusting the relative sound level After installing your speakers, you will have to find a good sound balance between the surround, center and front speakers. In the instruction booklet of your appliance you will find a section describing how to adjust the sound of the different speakers. Follow those instructions to get the most out of your new speakers. Setting the input sensitivity A.B.C Depending on which sound source you use, the signals delivered have different strengths. If the red light on the front of the transmitter unit starts to blink, the incoming signal is too strong. This will cause distortions. Set the A·B·C switch to adjust the input sensitivity to a lower level. If the red light on the front of the transmitter unit goes off during play, the incoming signal is not strong enough. Set the A·B·C switch to adjust the input sensitivity to a higher level. Setting the transmitting channel In case of signal interference from the transmitter it is possible to change to another transmitting channel. 1 Switch off both active surround speakers. 2 Set the CHANNEL slide at the back of the transmitter to another number. SETTING UP FB219W (for model FW798W only) L CENTER R FRONT TV FRONT SURR PRE OUT SURR 14 V SURROUND REAR MAINS SURROUND REAR MAINS STEREO FM BACK HSD REPEAT REC NEWS T.A. AMMW LW SOUND NAVIGATION INCREDIBLE SURROUND DIGITAL SOUND CONTROL DISC CHANGE DISC 1 DISC 2 DISC 3 OPEN•CLOSE DYNAMIC BASS BOOST CD TAPE PROG CLOCK/ TIMER NEWS! RDS DOLBY B NR DUB (HSD) REC STANDBY•ON SIDE A•B REVERSE TUNER AUX PRESET s s DEMO SEARCH • TUNING STOP•CLEAR PLAY PAUSE PREV NEXT 3CD CHANGER MINI HIFI SYSTEM CD1 • 2 • 3 BAND TAPE 1 • 2 CDR TIMER FRONT 60Hz 250Hz 500Hz 1KHz 2KHz 4KHz 8KHz VOLUME PROGRAMSHUFFLE S S L R C PRO LOGIC Untitled-7 14 6/15/00, 12:50 PM SETTING UP FB219W (for model FW798W only) DOLBY PRO LOGIC EnglishPress CD, TUNER, TAPE or AUX to TEST TONEUTE CENTER 3 Set the CHANNEL slide at the back of 1 General Information Dolby Pro Logic both active surround speakers to the switch on the system. Any amplifier or receiver used at high This state of the art Dolby Pro Logic mini same number as on the transmitter. 2 Press TEST TONE. power can produce distortions which may system enables you to experience and 4 Switch on both active surround . A test signal is seriously damage your speakers. If enjoy a Home Cinema sound ambience. The speakers. generated; it will distortion occurs, reduce the volume and Pro Logic system allows more accurate move through the Note: the tone control to a level where the sound definition of the individual sound sources. Left, Center, Right, – Always be sure that the transmitter and is acceptable again. It produces greater sound separation and Surround speakers, in that order. the active surround speakers are between channels and provides pinpoint W...
Эта инструкция также подходит к моделям:Музыкальные центры - FW768P/22 (1.18 mb)