Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
To stop recording . Press 70 on tape deck 1. 22 CD Synchronised start recording 1 Press CD 1/2/3 to select the disc. . You can programme the tracks in the order you want them to be recorded (refer to “CD Operation - Programming the disc tracks”). 2 Press . on tape deck 1 to star t recording. . The disc will star t playback automatically. To stop recording . Press 70 on tape deck 1, then press C to stop disc playback. Dubbing tapes 1 Load the prerecorded tape in tape deck 2. . Make sure both tapes have their full spool to the left. 2 Press A on tape deck 1 and followed by .. 3 PressEon tape deck 2. . Recording will start automatically. . Dubbing of tapes is possible on one side of the tape only. To continue recording on the reverse side, at the end of side A, flip the tape to side B and repeat the procedure. To stop dubbing . Press 70 on tape deck 1 and 2. Notes: – Dubbing of tapes is possible only from tape deck 2 to tape deck 1. –To ensure good dubbing, use tapes of the same length. Tape Operation / Recording 23 English 24 English Clock/Timer CD1 CD2 CD3 IMPORTANT! When in Eco Power standby mode, it is not possible to show the clock time or set the clock/timer function. View clock The clock (if it is set) will be shown in standby mode. To view the clock in any source mode (CD or TUNER for example) . Press CLOCK•TIMER. . The clock is displayed for a few seconds. . If the clock has not been set, "--:--" is displayed. Clock setting The clock can be set in either 12-hour or 24-hour mode ("12:00 AM" or "00:00" for example) 1 In standby or view clock mode, press CLOCK•TIMER once. In other source mode, press CLOCK•TIMER twice. 2 Press PROGRAM repeatedly to select clock mode. . "12:00 AM" or "00:00" starts flashing. 3 Press a or a on the system repeatedly to set the hour. 4 Press i or e on the system repeatedly to set the minute. 5 Press CLOCK•TIMER again to store the setting. . The clock starts working. To exit without storing the setting . Press Con the system. Notes: – The clock setting will be cancelled when the power cord is disconnected or if a power failure occurs. – During clock setting, if no button is pressed within 90 seconds, the system will exit clock setting mode automatically. Timer setting The system can switch on to CD or TUNER mode automatically at a preset time, serving as an alarm to wake you up. IMPORTANT! – Before setting the timer, ensure that the clock is set correctly. – The timer will always be switched on after it has been set. – The timer will not start if a recording is in progress. – The volume of the timer will increase gradually to the last tuned volume level. If the last tuned volume level is too low, the set will then increase to a predetermined minimum audible level. Clock / Timer 1 Press and hold CLOCK•TIMER for more than two seconds to select timer mode. . "12:00 AM" or "00:00" or the last timer setting star ts flashing. . star ts flashing. 2 Press CD 1/2/3 or TUNER to select the desired source. . “CD1 [or 2, 3] XX:XX" indicates the CD mode is selected. . “TU XX:XX” indicates the Tuner mode is selected. . Before setting timer, make sure the music source has been prepared. CD 1/2/3 – Load the disc(s). TUNER – tune to the desired radio station. 3 Press a or a on the system repeatedly to set the hour for the timer to star t. 4 Press i or e on the system repeatedly to set the minute for the timer to start. 5 Press CLOCK•TIMER to store the timer. . "TIMER ON" is displayed, followed by the set timer "XX:XX" and the selected source. . remains on the display. . At the preset time, the selected source will play. To exit without storing the setting . Press Con the system. Notes: – When the preset time is reached and the selected disc tray is empty, the next available disc will be selected. If all the disc trays are not available,Tuner will be selected automatically. – During timer setting, if no button is pressed within 90 seconds, the system will exit timer setting mode automatically. Deactivating the timer 1 Press and hold CLOCK•TIMER for more than two seconds. 2 Press C on the system to cancel the timer. . "CANCEL" is displayed and the disappears. Activating the timer (for the same preset time and source) 1 Press and hold CLOCK•TIMER for more than two seconds. 2 Press CLOCK•TIMER again to store. . The last set timer information is displayed for a few seconds and is shown. Sleep timer setting The sleep timer enables the system to switch to standby mode automatically at a preset time. 1 Press SLEEP on the remote control repeatedly to select a preset time. . The selections are as follows (time in minutes): 15 ™ 30 ™ 45 ™ 60 ™ 90 ™ 120 ™ OFF ™ 15 … . "SLEEP XX" or "OFF" is displayed. "XX" is the time in minutes. 2 When you reach the desired length of time, stop pressing the SLEEP button. . is shown, except for "OFF" mode. . The sleep timer is now set. Before the system switches to standby mode, a countdown of 10 seconds is displayed. "SLEEP 10" ™ "SLEEP 9".... ™ "SLEEP 1" ™ "SLEEP" To che...