Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
English 17 English Getting Started To deactivate Progressive manually . When the distorted sign still appears on the TV, it may be because the connected TV does not accept progressive signals, and progressive is set by mistake.You must reset the unit to interlace format. 1 Turn off your TV progressive scan mode or turn on to interlaced mode (refer to your TV user manual). 2 Turn off progressive scan by selecting “OFF” under PROGRESSIVE menu, then pressing OK on the remote control. . Progressive scan is turned off. Step 3: Setting language preference You can select your own preferred language settings.This DVD system will automatically switch to the selected language whenever you load a disc. If the language selected is not available on the disc, the disc’s default language will be used instead.The OSD language in the system menu will remain once selected. Setting the OSD Language 1 In disc mode, press SYSTEM MENU 2 Press a / a / 4 / 3 keys on the remote control to navigate in the menu. . Move to “General Setup Page” and press 4. . Move to “OSD Lang” and press a. 3 Press 4 / 3 to select a language and press OK. To remove the menu Press SYSTEM MENU. Setting the Audio, Subtitle and Disc Menu language – – Preference Page – – Audio Subtitle Disc Menu Parental Password Divx Subtitle Default English Spanish Portuguese Chinese Thai 1 In disc mode, press SYSTEM MENU 2 Press a / a / 4 / 3 keys on the remote control to navigate in the menu. . Move to “Preference Page” and press 4. . Move to one of the following and press a. – “Audio” (disc’s soundtrack) – “Subtitle” (disc’s subtitles) – “Disc Menu” (disc’s menu) 3 Press 4 / 3 to select a language and press OK. To remove the menu Press SYSTEM MENU. 18 Basic Operations IMPORTANT! – Before you operate the system, complete the connection procedures. – When the system is switched to Standby mode, it is still consuming power.To disconnect the system from the power supply completely, reomve the AC power plug from the wall socket. Plug and Play (for tuner installlation) Plug and Play allows you to store all available radio stations automatically. First time setup/power up 1 When you turn on the main supply, "AUTO INSTALL -PRESS PLAY " is displayed. 2 Press EA on the system to star t installation. . "PLUG AND PLAY" .... "INSTALL" is displayed, followed by "TUNER" and "AUTO". . PROG star ts flashing. . The system will automatically store the radio stations (FM only ) with sufficient signal strength. . When all the available radio stations are stored or the memory for 20 presets are used, the last preset radio station will be played. To reinstall Plug and Play 1 In standby mode, press and holdEA on the system until "AUTO INSTALL -PRESS PLAY" is displayed. 2 Press EA again to star t installation. . All previously stored radio stations will be replaced. To exit without storing the Plug and Play . Press 9 on the system. . If you do not complete the Plug and Play installation, the function will be restarted when you next turn on the main supply again. Notes: – If no stereo frequency is detected during Plug and Play, "CHECK ANTENNA" will be displayed. Switching the system on/off . In standby/Eco-power standby mode, press STANDBY-ONB or SOURCE on the set, or DISC, USB, FM or AUX on the remote to switch on the system. . The system will switch to the selected or last selected source. To switch the system to standby mode . In power-on mode, press briefly STANDBYONB (B on the remote). . The clock time will be displayed. Or "--:--" will be displayed if clock time is not set. To switch the system to Eco-power standby mode . In power-on mode, press and hold STANDBYONB (B on the remote). . “ECO POWER” is displayed briefly. . Eco-power lamp B on the front panel will light up. . The LCD display will go blank. Helpful hints: – Pressing and holding B on the remote can switch between Eco-power standby and normal standby. Power saving automatic standby As a power-saving feature, the system will automatically switch to Standby mode if you don’t press any button within 15 minutes in the stop mode. English 19 Basic Operations English Volume control Press VOLUME (or VOL +/-on the remote) LOUDNESS feature enables the system to to increase or decrease the volume level. automatically increase the treble and bass sound LOUDNESS . The display briefly shows ”VOL” and a volume effect at low volume (the higher the volume, the value from “01” to “31” ( “MIN” or “MAX” is lower the treble and bass increase). displayed when adjusted to the lowest or highest . Press and hold LOUD/DBB on the remote volume level). control to enable/disable LOUDNESS feature. . icon appears/disappears after this feature To switch off the volume temporarily is enabled/disabled. . Press MUTE on the remote. . Playback will continue without sound and “MUTE” appears. . To activate sound reproduction, you can: – press MUTE again; – adjust the volume controls; – change source. Sound Control DBB (Dynamic Bass Boost) DBB enhances the bass respo...