Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Auto tuning : When the TUNING/TIME (%UP or fiDOWN) button is pressed for more than 0.5 second, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Notes : • When radio interference occurs during auto scan tuning, auto scan tuning may stop automatically at that point. • If a weak station signal is found during auto scan tuning, the station will be skipped. • To stop the auto tuning, press the TUNING/TIME (%UP or fiDOWN) button again. 5To receive an FM stereo transmission, press the TUNER (BAND) button so that the “ST.” indicator on the display lights up. • “ ” will light up when an FM broadcast is in stereo. 6 If the FM reception is weak, press the TUNER (BAND) button so that the “ST.” indicator goes off. • The reception changes to mono, the sound becomes clearer. 18 EN P.CALL 4 1 . . MEMORY/ SET MEMORY/ SET P.CALL 4 1 . . P.CALL 4 1 . . MEMORY/ SET MEMORY/ SET P.CALL 4 1 . . Preset tuning You can store up to 40 stations in memory (40 stations consisting of any combination of FM and AM stations you like) and recall them at the push of a button. To enter stations into memory : 1 Perform steps 1 -6 in the “Tuning” section (page 18). 2 Press the MEMORY/SET button. • “PGM” and the preset channel number will flash. 3 Within 30 seconds, press the P. CALL (4 1 or . .) button to make the preset channel number flash in the display. • The order of the station stored in memory, starts with preset channel 1. 4 Within 30 seconds, press the MEMORY/SET button to store that station in the selected station preset number memory. • If the “PGM” and preset number go out before the station is memorized, repeat the operation from step 2. 5 Repeat steps 1 -4 to set other preset stations, or to change a preset station. • When a new station is stored in the selected station preset number memory, the previous stored contents will be erased. To recall a memorised station : Press the P. CALL (4 1 or . .) button for less than 0.5 second to select the desired station. • The stations (preset channel number, frequency band) which have been stored in memory will appear in the display in numerical order, irrespective of the frequency bands. Notes : • When searching for a memorized station, do not press the P. CALL (4 1 or . .) for more than 0.5 second. • When the P. CALL (4 1 or . .) button is pressed for more than 0.5 second, the unit will enter the preset memory scan mode. Backup function : The backup function protects all station presets for a few hours should there be a power failure or the AC power cord is removed from the AC socket. 19 EN P.CALL 4 1 . . P.CALL 4 1 . . EX.BASS /DEMO POWER ON/STANDBY TUNER (BAND) P.CALL 4 1 . . P.CALL 4 1 . . EX.BASS /DEMO POWER ON/STANDBY TUNER (BAND) Preset memory scan The stations saved in the preset memory can be scanned automatically. 1To scan the preset stations, press the P. CALL (4 1 or . .) button for more than 0.5 second. • The station preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each. 2 Press the P. CALL (4 1 or . .) button again to stop the memory scan at the desired station. Note : When the preset memory dose not have any stations stored in it, the preset memory scan will not function. To erase all the contents in the preset memory : 1 Press the POWER / ON/STANBY button to enter the standby mode. 2 Press the POWER / ON/STANDBY button whilst holding down the TUNER (BAND) button and the SOUND MODE button. • “PGM” will light up and “TUNER CL” will appear. • After performing this operation, all of the preset memory information will be erased. 20 EN CASSETTE OPERATION 44 1 2,5 3 6 P.CALL 4 1 . . 2,5 6 7 P.CALL 4 1 . . 1 3 7 STOP REVERSE MODE TAPE A or TAPE B playback 1 Press the POWER / ON/STANDBY button to turn the power on. 2 Press the TAPE (A/B) button. 3 Open the cassette door by pushing the area marked “PUSH OPEN”. 4 Load the cassette into the TAPE A or TAPE B cassette compartment. 5 With cassette in both decks, press the TAPE (A/ B) button to switch operation from one deck to the other. 6 Press the 3 button to start playback. • When playback is performed using the remote control, press the 3 button. To stop playback : Press the 7 STOP button. Fast forward/rewind : 1 Press the 7 STOP button, then press the TAPE (A/B) button to select TAPE A or TAPE B. 2 To advance the tape, press the P. CALL . . button. To rewind it, press the P. CALL 4 1 button. Caution : • To remove the cassette tape, press the 7 STOP button, and then open the cassette compartment. • Before changing from one tape operation to another, press the 7 STOP button. • If a power failure occurs during tape operation, the tape head will remain engaged with the tape and the cassette door will not open. In this case, wait until power is restored. Selection of reverse mode (Tape B only) : Press the REVERSE MODE button repeatedly to select the following setting : • “ ” ....Playback stops after having played both sides of tape in a deck...
Эта инструкция также подходит к моделям:Музыкальные центры - XD-A55 (1.64 mb)