(High-speed recording is not available.) The recording source can be a finalized CD-R/RW, but digital-to-digital recording may not be available with certain discs.”Digital recording and SCMS” A Select the “CD” input. Be sure to put the CD recorder in stop mode. Application section Make the preparations for recording. When digital-to-digital recording is not impossible or when analog-to-digital recording is performed, select the analog input as described in the follow- ing section then start the setting from step 1below.”Changing the recording input setting”eBefore recording 1 1Place a recordable CD-R or CD-RW disc. fl2Load the recording source disc in the CD player. . 3Make sure that the "High" (high-speed dubbing indicator) in the display is not lit. 2 2 Check the current play mode of the CD player. Program the desired sequence of CD tracks. If it is in play mode, stop it. 7 3 Perform steps 2 and 3 of the procedure in ”Lis- tening in the desired sequence (Program play- back)”. u 4 4 Start recording. CD=CDR DIGITAL The current setting is displayed. "DIGITAL" is lit ............. Digital-to-digital recording "DIGITAL" not lit: ......... Analog-to-digital recording . When a CD-R/RW is loaded in the CD recorder, the CD-R IN indicator may blink for a while. “OPC (Optimum Power Control)” ‡ . If the "HIGH" is lit in the display, turn it on by selecting "O.T.E. Speed" in the menu mode, selecting "" and pressing the SET key. . High-speed recording is not available in the PGM mode. . Recording starts with the first programmed track until all the programmed tracks have been recorded. . When either the CD program playback or CDR recording operation stops, the other operation also stops. . When you are operating the main unit, select "O.T.E. Mode" in the menu mode, then select "CD= =====CDR " and press the SET key to start recording. . With certain discs, digital-to-digital recording may be prohibited by SCMS (A). Such a disc should be recorded using the analog output signal. e 63Convenient recording of CD player output . "CDR Writing" is displayed when recording completes. Display "CDR Writing" indicates that recorded data is being written in the CD-R/RW. Do not apply vibrations or impact during recording and "CDR Writing" display. If the power cord is unplugged from the power outlet or a power failure occurs during recording, the disc data may be destroyed and the disc may become unusable. During digital-to-digital recording, the CD recorder may encounter a track with which digital-to-digital recording is prohibited. In this case, "SCMS"(A) is displayed and recording pauses temporarily, but playback of the source continues and recording restarts whenever a track with which digital-to-digital recording is permitted is encountered. However, if "SCMS" is displayed with the first track to be recorded, the track as well as the subsequent tracks will not be recorded. To interrupt a recording To finalize the recorded CD-R/RW . Press the 7 (stop) key on the main unit or 7 STOP key on the remote. (This stops both recording and playback.) Application section 64 Convenient recording of CD player output 64 Convenient recording of CD player output (O.T.E.) CD = TAPE Records all tracks in a CD with a simple operation. (All-track recording) Records a single CD track being played from the beginning. (Single-track recording) Do not use a cassette tape with more than 90-minute recording time, for the tape used with such a cassette is very thin and tends to cause troubles such as entanglement around the pinch roller or cutting of tape. Be sure to put the cassette deck in stop mode. 1 1 Make the preparations for recording. 2 2 Check the current play mode of the CD player. 1Perform steps 1~3 of the procedure in ”Recording on TAPE”. ‚ 2Load the recording source disc in the CD player. . High (TYPE (TYPE This system can record signals on Normal (TYPE ) and ) position tapes. Remember that the Metal ) tapes cannot be used with this system. All track recording Single-track recording If it is in play mode, stop it. Select the desired CD track and play it. Start recording.3STOP76CD .Even when the O.T.E. CD=====TAPE key is pressed in the middle of a track, recording will start from the beginning of the track. Application sectionCD=TAPE To interrupt a recording . When either the playback or recording operation stops, the other operation also stops. . When you are operating the main unit, select “O.T.E. Mode” in the menu mode then select “CD= =====TAPE“ and press the SET key to start recording. . When recording completes, the tape stops after leaving a no- sound blank of about 4 seconds. Press the 7 (stop) key on the main unit or 7 STOP key on the remote. (This stops both recording and playback.) 65Convenient recording of CD player output 65Convenient recording of CD player output (PGM mode + O.T.E.) CD = TAPE Desired CD tracks can be programmed in the desired sequence and recorded onto a tape. Do not use a cassette tape with more than ...
)
