Оценок - 5, средний балл: 4.2
(
)
)
|
Фрагмент инструкции
Front speaker (Right) Front speaker (Left) Rear speaker (Left surround) Subwoofer Center speaker 1. Stick the speaker stand to the speaker. 2. Detach the speaker cover on the rear of the speaker, and then connect the speaker stand and the speaker by screws. 3. Pull the speaker cable through the hole on the speaker stand, and then draw the speaker cable through the hole on the bottom of the speaker stand. 4. Connect the speaker cable to the appropriate terminals on the rear of speaker, and then attach the speaker cover. Speaker stand Speaker cover Hole Hole to hang the speaker on the wall Rear speaker (Right surround) 9 Installation and Setup Assembling the speaker stand to the speaker Before connecting the speakers, assemble the speaker stand to the speaker as illustrated. Tip: You can use the speaker without the speaker stand by installing it on the wall. Speaker System Connection Connect the speakers using the supplied speaker cables. To obtain the best possible surround sound, adjust the speaker parameters (volume, distance, etc.). Notes: Be sure to match the speaker cable to the appropriate terminal on the components: + to + and – to –. If the cables are reversed, the sound will be distorted and will lack base. If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on the speakers. Front speaker (Right) Front speaker (Left) Rear speaker (Left surround) Subwoofer Center speaker 1. Stick the speaker stand to the speaker. 2. Detach the speaker cover on the rear of the speaker, and then connect the speaker stand and the speaker by screws. 3. Pull the speaker cable through the hole on the speaker stand, and then draw the speaker cable through the hole on the bottom of the speaker stand. 4. Connect the speaker cable to the appropriate terminals on the rear of speaker, and then attach the speaker cover. Speaker stand Speaker cover Hole Hole to hang the speaker on the wall Rear speaker (Right surround) HDMI Connection About HDMI HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for an easy all- digital output to an HDMI or DI-equipped TV. Connection to an HDMI TV requires an HDMI cable while connection to a DVI-equipped TV requires a DVI adapter besides a HDMI cable. HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multi-channel surround-sound audio, HDMI features include uncompressed digital video, a bandwidth of up to 5 gigabytes per second, one connector (instead of several cables and connector), and communication between the AV source and AV devices such as DTVs. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC. If you have a HDMI TV or monitor, you can connect it to this DVD/CD Receiver using a HDMI cable. 1. Connect the HDMI OUT jack on the DVD/CD Receiver to the HDMI jack on a HDMI compatible TV or monitor (H). 2. Set the TV’s source to HDMI (refer to owner’s manual for TV). 3. In the stop mode, select HDMI mode by pressing HDMI. Press RESOLUTION repeatedly to select the resolution you wish to change. Notes: • The arrow on the cable connector body should face up for correct alignment with the connector on the DVD/CD Receiver. • If HDMI cable is not connected, the HDMI button does not operate. • If there is noise or there are lines on the screen, please check the HDMI cable. • Not all HDCP-compatible DVI devices will work with this DVD/CD Receiver. • If TV does not support HDCP, snow noise appears on the screen, or picture may be vibrated. Tip : When you use HDMI connection, you can change the resolution (480p or 576p, 720p, 1080i) for the HDMI output by pressing RESOLUTION on the Remote Control. Important Note If you turn off the TV or disconnect the HDMI cable during playback of the device, playback will pause. You have to click on the play button to play back again. For some TVs, when you change the TV mode, such condition specified above may happen. Rear of DVD/CD Receiver OUT PUT INPUT L -AUX - R MONITOR Y COMPONENT VIDEO (PROGRESSIVE SCAN) HDMI H HDMI compatible TV Resolution setting You can change the resolution for the COMPONENT VIDEO OUT by pressing RESOLUTION on the Remote Control. Available resolution settings are as shown below. OUTPUT Available Resolution CONNECTION PAL NTSC HDMI VIDEO OUT 1920 x 1080i 1280 x 720p 720 x 576p 1920 x 1080i 1280 x 720p 720 x 480p COMPONENT VIDEO OUT 1920 x 1080i 1280 x 720p 720 x 576p 720 x 576i 1920 x 1080i 1280 x 720p 720 x 480p 720 x 480i MONITOR OUT 720 x 576i 720 x 480i SCART 720 x 576i - Notes: • If the picture does not appear on the screen with the analog video connections, change the resolution to 480i (or 576i). • For 720p and 1080i resolution on the component video out, only non-copy protected discs can be played back. If the disc is copy protected, it will be displayed at the 576p(PAL) 480p(NTSC) resolution. • 1080i, 720p,...