Оценок - 4, средний балл: 3.5
(
)
)
|
Фото и характеристики Samsung MM-L4 |
Фрагмент инструкции
20 Technical Specifications ............................................................................................................. 21 3 GB Front Panel View On/Standby Push Open VolumeRepeatA B Mute CD Sync. Band Tuning Mode UpDown PTY RDS Display REC/ Pause EQ S.Bass Power Sound Push Eject TUNER TAPE AUX CD 1 8 9 10 11 12 13 14 15 16 2 5 3 4 6 7 On/Standby Push Open VolumeRepeatA B Mute CD Sync. Band Tuning Mode UpDown PTY RDS Display REC/ Pause EQ S.Bass Power Sound Push Eject TUNER TAPE AUX CD 1 8 9 10 11 12 13 14 15 16 2 5 3 4 6 7 1. On/Standby button 2. TAPE/CD Repeat (A B) button 3. PTY button(RDS) 4. Display button(RDS) 5. CD Synchro button 6. REC/Pause button 7. Function control buttons 8. CD Push Open button 9. Function selection buttons (TUNER/CD/TAPE) 10. Volume control buttons 11. Mute button 12. EQ button 13. S. BASS button 14. Push Eject button 15. Power Sound button 16. AUX button 4 GB Rear Panel View 2 3 4 1 5 6 2 3 4 1 5 6 1. MIC JACK CONNECTOR(OPTIONAL) 2. HEAD PHONES JACK CONNECTOR 3. AM AERIAL CONNECTOR TERMINALS 4. FM AERIAL COAXIAL CONNECTOR TERMINALS 5. AUX INPUT 6. LOUDSPEAKERS CONNECTOR TERMINALS 5 GB Remote Control On/Standby Timer On/Off TAPE EQ Preset Power Sound Sleep CD Repeat Mono/ST. TUNER Band Program/Set AUX Timer/ Clock CD CDCD VOL. VOL. TUNING MODE 1 9 13 15 11 17 18 19 20 10 12 14 16 2 7 4 3 5 6 8 On/Standby Timer On/Off TAPE EQ Preset Power Sound Sleep CD Repeat Mono/ST. TUNER Band Program/Set AUX Timer/ Clock CD CDCD VOL. VOL. TUNING MODE 1 9 13 15 11 17 18 19 20 10 12 14 16 2 7 4 3 5 6 8 1. On/Standby button 2. EQ Preset button 3. Power Sound button 4. Sleep button 5. CD Repeat button 6. Tape rewind and fast-forward buttons 7. CD Stop and cancel button 8. CD Track or radio station search buttons 9. Timer/Clock Setting button 10. Timer on/off button 11. AUX button 12. Program/Set button 13. Frequency band selection button 14. Mono/Stereo button 15. Tape Playback button 16. Tape stop(playback/record) button 17. CD Play and pause button 18. Volume increase button 19. Tuning Mode button 20. Volume decrease button 6 Where to Install Y our Micro-Component System Connecting the Loudspeakers GB To take full advantage of your new MICRO component system, follow these installation instructions before connecting the unit. Install the system on a flat, stable surface. Never place this unit on carpeting. Never locate this unit in an outdoor area. Maintain an open space of approximately 4 inches (10 cm) on the sides and rear of the system, for ventilation purposes. Make sure that you have enough room to open the compact disc compartment easily. Place the loudspeakers at a reasonable distance on either side of the system to ensure good stereo sound. Direct the loudspeakers towards the listening area. For optimum performance, make sure that both speakers are placed at an equal distance above the floor. The loudspeaker connector terminals are located on the rear of the system (red and black tabs). There are four terminals on the system: Two for the left speaker (marked L) Two for the right speaker (marked R) To achieve the correct sound quality, connect the: Red wire to the + terminals Black wire to the -terminals 1 To connect a wire to a terminal, push the tab as far as it will go: To the right on the system and hold it in position 2 Insert the wire, up to the plastic sheathing, in the hole. 3 Push the tab back: To the left on the system, release the tab. Result: The wire is pinched and held firmly in place. 4 Repeat the operation for each wire. On/Standby Push Open VolumeRepeatA B Mute CD Sync. Band Tuning Mode UpDown PTY RDS Display REC/ Pause EQ S.Bass Power Sound Push Eject TUNER TAPE AUX CD R L Inserting Remote Control Batteries Connecting Y our System to the Power Supply Insert or replace remote control batteries when you: The main lead must be plugged into an appropriate socket. Purchase the Micro component system Find that the remote control is no longer operating Before plugging your system into a main socket, you must correctly check the voltage. When replacing the batteries, use a new set of batteries and never mix alkaline and manganese batteries. 1 Plug the main lead (marked AC CORD on the rear of the system) into an appropriate socket. 1 Place your thumb on the position marked on the battery 2 Press the On/Standby button to switch your Micro component compartment cover (rear of the remote control) and push the system on. cover in the direction of the arrow. 2 Insert two AAA, LR03 or equivalent batteries, taking care to respect the polarities: + on the battery against + on the remote control – on the battery against – on the remote control 3 Replace the cover by sliding it back until it clicks into position. 7 GB 8 The AM(MW)/LW aerial (for long and medium waves) can be: Placed on a stable surface Fixed to the wall (you must first remove the base) The AM aerial connector terminals are located on the rear of the system and are marked AM. To avoid noise interference, ...