Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
(Refer to the operating instructions of the remote-control transmitter for details about the functions available on the remote-control transmitter.) While listening to music Adjust the tone quality as desired. 1. Press the VCR 1>monitor switch of the amplifier. (The indicator will illuminate.) 2. Adjust the tone quality as desired. (Refer to the operating instructions of the equalizer for details.) Adjust the volume level. Press this button to boost the ultra*low frequency range. (The indicator will illuminate.) (За? ееэозшв сйй m Ш ©изкштЭ : 1. Select the desired audio source on the amplifier. 2. Set the input selector of the AV surround processor to “Source”. 3. Adjust the surround-sound effect. (Refer to the operating instructions of the AV surround processor for details.) After listening is finished Be sure to reduce the volume level, and switch OFF the power to each unit. — 12 — Listening to Phono Discs Have you completed the “Standard Operating Procedures” (page 12)? 1 Press the input selector on the amplifier marked "phono.” (The input selector/volume level display on the amplifier shows "PHONO”.) Turntable Set to the appropriate speed. Place a disc on the platter mat. ► Set to to stop the play temporarily. Set to to resume the play. i Press to stop the play. Remove the stylus protector. (The tape on side of cartridge prevents the stylus assembly from shaking loose during shipment.) Move to the desired position. (The platter will start turning.) Set to “I”. (Play will start.) 8 Adjust the volume level and the tone quality as desired. (Refer to page 12.) ■ For a 17 cm (7”) (large center hole) disc ■When play ends The tonearm will automatically return to the arm rest (the automatic return feature.) ■ After use Attach the stylus protector. ■ Operation note When the unit is used for the first time, or after it has been moved from one place to another, it may happen that the automatic return function might not operate correctly due to vibrations during transport or movement. If this happens, press the stop switch. (The tonearm will return and thereafter the operation will be normal.) — 13 — Memory Presettings With this unit you may preset as many as 24 radio broadcast stations: FM/AM random presetting. After broadcast stations have been preset as described below, any desired station can be quickly and easily selected. Stations can be freely preset to any desired channel. Have you completed the “Standard Operating Procedures” (page 12)? 1 Press the input selector on the amplifier marked “tuner”. (The input selector/volume level display on the amplifier shows “TUNER”.) Channel display < Memory indicator Press the appropriate tuning button to tune to the desired broadcast. Tuning Press the left button to change the frequency downward, and press the right button to change the frequency upward. • Automatic tuning Press the button. When the frequency indication begins to change, release the button (a broadcasting station will be selected automatically). Repeat this operation untit the desired station is found. • Manual tuning © Press the button and hold slightly (frequency will change continuously). (g) Release it when approaching the desired exact frequency, and then press the button again momentarily (frequency change will stop). (3) Press the button momentarily (frequency will change each time the button is pressed), and tune to the desired frequencies. Press the “FM” or “AM” button. Tuner Select the desired “channel”. I [A maximum of 24 broadcast stations (AM and/or FM) can be memorized ] Example: To select “channel” 12;_ Press I 1 I and then | 2 |. Note: Make the entry without interruption between steps.lf there is an interval of about two seconds or more between steps, you may not obtain the desired settings. In this case, perform steps 4-5 again to reset the memory as necessary. (If the correct presetting cannot be confirmed on the channel display, then reset the memory.) Press. (The memory indicator will illuminate.) Enter the name (call sign, etc.) of the preset broadcasting station on the station memory file sheet. (Refer to page 15.) This completes the procedures for presetting radio broadcast frequencies. The other preset-tuning buttons can be preset in the same way by following steps 2 through 6. -Note:- If a new broadcasting station is preset into a channel, the broadcasting station which was previously entered in that channel will be automatically erased. “Most-recent” memory The most-recent memory is a system by which the unit ”remembers" the FM or AM broadcast station last heard when this unit is switched OFF, and automatically tunes to that station the next time the power is switched ON. “Back-up” memory This Is the function which preserves the preset memory and most-recent memory functions. In the event of a power failure, or if the unit is not used for a long period of time, the back-up memory will preserve the p...